TP-Link TL-WA901ND manual Status

Page 26

TL-WA901ND300Mbps Wireless N Access Point User Guide

4.2Status

Selecting Status will enable you to view the AP’s current status and configuration, all of which is read-only.

Figure 4-3 Device Status

Firmware Version - This field displays the current firmware version of the AP.

Hardware Version - This field displays the current hardware version of the AP

Wired - This field displays the current settings or information for the Network, including the MAC address, IP address and Subnet Mask.

Wireless - This field displays basic information or status for wireless function, including

Operating Mode, Wireless Network Name, Channel, Mode, Channel Width, Max Tx Rate and MAC Address.

Traffic Statistics - This field displays the AP's traffic statistics.

System Up Time - This filed displays the run time of the AP since it’s powered on or reset.

Note:

If you select Client mode in Figure 4-12,the wireless status in Figure 4-3will change, similar to the figure below:

18

Image 26

Contents TL-WA901ND Copyright & Trademarks FCC Statement Korea Warning Statements Safety Information Product Description 300Mbps Wireless N Access Point Yang Hongliang Product Manager of International BusinessContents Factory Defaults Backup & Restore Reboot Password System Log Package Contents Conventions IntroductionProduct Overview Front Panel Main FeaturesAppearance LED Explanation Name Status Indication Used as Reset button Rear PanelTL-WA901ND  Used as WPS buttonBefore You Begin Hardware InstallationConnecting the Device Basic Requirements Note TL-WA901ND300Mbps Wireless N Access Point User Guide Quick Installation Guide Quick SetupQuick Setup TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide 12 Network Setting 13 Quick Setup Finish Configure the Device LoginStatus WPS Device Status ClientMethod One To add a new deviceBy PBC Method Two Method Three Add a New DeviceII. By PIN Enter the PIN Click ConnectNetwork Wireless Wireless Settings Wireless menu Note TL-WA901ND300Mbps Wireless N Access Point User Guide Configure the Access Point TL-WA901ND300Mbps Wireless N Access Point User Guide Port Configure the SwitchEgress Rule Processing mode of Utag Frames  Note 13 Wireless Settings in Repeater mode 14 Wireless Settings in Repeater mode TL-WA901ND300Mbps Wireless N Access Point User Guide 15 Wireless Settings in Bridge with AP mode Wireless Security Access Point TL-WA901ND Multi-SSID Client TL-WA901ND300Mbps Wireless N Access Point User Guide WDS Repeater 20 Wireless Security Repeater Universal RepeaterTL-WA901ND300Mbps Wireless N Access Point User Guide Bridge with AP TL-WA901ND Wireless MAC Filtering To set up an entry, follow these instructions To modify or delete an existing entryWireless Advanced Wireless Statistics Throughput MonitorDhcp 27 The Dhcp menuDhcp Settings Dhcp Clients List Address ReservationTo modify a Reserved IP address System ToolsTo Reserve IP addresses To delete all Reserved IP addresses Click Clear AllSnmp 31 The System Tools menuDiagnostic TL-WA901ND300Mbps Wireless N Access Point User Guide 34 Diagnostic Results Ping Watch DogFirmware Upgrade To upgrade the devices firmware, follow these instructionsFactory Defaults Backup & RestoreReboot PasswordSystem Log Appendix a Application Example TL-WA901ND TL-WA901ND300Mbps Wireless N Access Point User Guide Common Default Settings Appendix B Factory DefaultsDefault Value WirelessAppendix C Troubleshooting T2. What can I do if I forget my password?Physical and Environment Appendix D SpecificationsGeneral Appendix E Glossary TL-WA901ND300Mbps Wireless N Access Point User Guide