TP-Link TL-WA901ND manual Wireless Settings in Repeater mode

Page 42

TL-WA901ND300Mbps Wireless N Access Point User Guide

Note:

To apply any settings you have altered on the page, please click the Save button, and then you will be reminded to reboot the device.

4)WDS Repeater: In WDS Repeater mode, the AP with WDS enabled will relay data to an associated root AP. AP function is enabled meanwhile. The wireless repeater relays signal between its stations and the root AP for greater wireless range.

Figure 4-13 Wireless Settings in Repeater mode

Wireless Name of Root AP - If you select the radio button before Wireless Name of Root AP, the AP client will connect to the AP according to SSID. Enter the SSID of AP that you want to access.

MAC Address of Root AP - If you select the radio button before MAC Address of Root AP, the AP client will connect to the AP according MAC address. Enter the MAC address of AP that you want to access.

Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the device can be used. It may be illegal to use the wireless function of the device in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance.

Note:

Limited by local law regulations, version for North America does not have region selection option.

Channel - Determines the operating frequency to be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.

Mode - Select the desired wireless mode. The options are:

•11b only - Only 802.11b wireless stations can connect to the device.

•11g only - Only 802.11g wireless stations can connect to the device.

34

Image 42

Contents TL-WA901ND Copyright & Trademarks FCC Statement Korea Warning Statements Safety Information Product Description 300Mbps Wireless N Access Point Yang Hongliang Product Manager of International BusinessContents Factory Defaults Backup & Restore Reboot Password System Log Package Contents Introduction Product OverviewConventions Front Panel Main FeaturesAppearance LED Explanation Name Status Indication Used as Reset button Rear PanelTL-WA901ND  Used as WPS buttonBefore You Begin Hardware InstallationConnecting the Device Basic Requirements Note TL-WA901ND300Mbps Wireless N Access Point User Guide Quick Installation Guide Quick SetupQuick Setup TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide 12 Network Setting 13 Quick Setup Finish Configure the Device LoginStatus WPS Device Status ClientTo add a new device By PBCMethod One Method Two Method Three Add a New DeviceII. By PIN Enter the PIN Click ConnectNetwork Wireless Wireless Settings Wireless menu Note TL-WA901ND300Mbps Wireless N Access Point User Guide Configure the Access Point TL-WA901ND300Mbps Wireless N Access Point User Guide Configure the Switch Egress Rule Processing mode of Utag FramesPort  Note 13 Wireless Settings in Repeater mode 14 Wireless Settings in Repeater mode TL-WA901ND300Mbps Wireless N Access Point User Guide 15 Wireless Settings in Bridge with AP mode Wireless Security Access Point TL-WA901ND Multi-SSID Client TL-WA901ND300Mbps Wireless N Access Point User Guide WDS Repeater 20 Wireless Security Repeater Universal RepeaterTL-WA901ND300Mbps Wireless N Access Point User Guide Bridge with AP TL-WA901ND Wireless MAC Filtering To set up an entry, follow these instructions To modify or delete an existing entryWireless Advanced Wireless Statistics Throughput MonitorDhcp 27 The Dhcp menuDhcp Settings Dhcp Clients List Address ReservationTo modify a Reserved IP address System ToolsTo Reserve IP addresses To delete all Reserved IP addresses Click Clear AllSnmp 31 The System Tools menuDiagnostic TL-WA901ND300Mbps Wireless N Access Point User Guide 34 Diagnostic Results Ping Watch DogFirmware Upgrade To upgrade the devices firmware, follow these instructionsFactory Defaults Backup & RestoreReboot PasswordSystem Log Appendix a Application Example TL-WA901ND TL-WA901ND300Mbps Wireless N Access Point User Guide Common Default Settings Appendix B Factory DefaultsDefault Value WirelessAppendix C Troubleshooting T2. What can I do if I forget my password?Appendix D Specifications GeneralPhysical and Environment Appendix E Glossary TL-WA901ND300Mbps Wireless N Access Point User Guide