Polycom DOC2231A manual Unpacking the MGC+50

Page 20

Chapter 2 - Hardware Installation

3.Release the clasp locks at the bottom, and lift the MGC+50 top cover.

Wood Packing Case

Foam Block

Foam Block

Figure 2-4: Unpacking the MGC+50

4.Lift the MGC+50 unit and remove the package base.

5.Lower the MGC+50 unit, placing it on the surface.

If you are rack mounting the MGC+50, allow a minimum clearance of 3 inches above the unit.

2-8

Image 20

Contents MGC+50/MGC+100 Getting Started Guide USA Regulatory Notices Singapore Certificate Table of Contents About Conferences Defining a New Audio Conference Page Before You Begin System OverviewNetwork Equipment, Numbers and Addresses Overview of the Getting Started Guide Management Tools Defining a New Audio ConferenceDefining a New Video Conference Hardware Installation MGC+100 Hardware Installation System SafetyInspecting the MGC+/ReadiManager IAM Package Contents General Safety PrecautionsRack Mount Safety Precautions Polycom MGC+/ReadiManager PrecautionsUnpacking and Positioning the MGC+100 MGC+100 packageUnpacking the MGC+100 Mounting the MGC+100 in a 23 Rack To unpack and position the MGC+50 MGC+50 Hardware InstallationUnpacking and Positioning the MGC+50 Unpacking the MGC+50 To install and mount the MGC+50 Mounting the MGC+50 on a RackTo connect to the AC Inlet Connecting and Setting Up the MGC+100/ MGC+50Connecting to the Power Source Connecting the MGC+100/MGC+50 to the Local Network Connecting the MGC+ to the Conferencing NetworkTo connect the MGC+ to the Isdn network or T1-CAS Network Isdn network connectionConnecting the MGC+ to the IP Network To update the LAN.cfg File First Entry MGC+ Control Unit CU IP ConfigurationUsing the Compact Flash Disk with the LAN.CFG File Press 1, to Change the MGC+ IP Settings Option DescriptionHardware Installation MGC+50/MGC+100 Getting Started Guide Option Description Using a Keyboard and Monitor Attached to the MGC+ unit MCU Properties dialog box opensType C\\mcu\cfgedit lan.cfg and press Enter MGC+ Software Installation and Configuration Initial ReadiManager IAM ConfigurationInstalling the MGC Manager To install the MGC Manager softwareMGC+ Software Installation and Configuration Starting the MGC Manager Application To start the MGC Manager applicationDefining the MCU To define an MCU ConnectionMGC+50/MGC+100 Getting Started Guide Connecting to an MCU To connect the operator workstation to an MCUIP Network Service Configuring the Network ServicesIsdn Network Service To define the Network Service Define the following parameters To configure a specific IP+ card DNS SIP To configure an Isdn Network Service Click OK Confirmation message is displayed Icon Description About Conferences On-Demand Reservation-less ConferencingScheduled Conferences Meeting RoomsVideo Conference Attributes Entry Queue Default Reservation Templates Reservation TemplatesStarting a Conference Reservations Database window opensBasic Operations Viewing the Conference Dial-in Properties Connecting to a Conference/Entry Queue Dialing-in to a Conference/Entry QueueISDN/PSTN Participants ParticipantsSIP participants Monitoring On Going Conferences General MonitoringExpand the On Going Conferences tree Participant Monitoring Filter dialog box opens Filtering Option DescriptionTo view the list of participants in the Browser pane Expand the On Going Conferences or Reservations treeTo list the participants in the Status pane Participant Level Monitoring To check the properties of a participantOperations Performed During On Going Conferences Adding a Participant to a ConferenceTo add a new participant to a Conference Properties Identification dialog box opensBasic Operations To add a pre-defined participant to a conference Conference Properties dialog box opensBasic Operations Making Dial-Out Connections To manually establish a Dial-out connectionDisconnecting Participants To disconnect a participantMuting a Participant To delete a participantLocking and Unlocking a Conference To mute a participant using MGC ManagerManager User’s Guide, Volume I, Chapter To Lock or Unlock a conference To change the duration of an On Going Conference To terminate a conference manually Changing the Layout in a Continuous Presence Conference Conference Properties Video Sources dialog box opensMGC+50/MGC+100 Getting Started Guide Defining a New Audio Only Entry Queue To define a new Audio Only Entry QueueEntry Queue Properties dialog box opens Defining a New Audio Conference MGC+50/MGC+100 Getting Started Guide Conference Properties General dialog box opens Defining an On Going Audio ConferenceTo define a new On Going Audio Conference MGC+50/MGC+100 Getting Started Guide Properties Settings dialog box opens MGC+50/MGC+100 Getting Started Guide Conference Properties Participants tab is displayed Defining a New Audio Only Meeting RoomTo define a New Meeting Room Click the Meet Me Per Conf tab Properties Meet Me Per Conf dialog box opensDefining a New Audio Conference MGC+50/MGC+100 Getting Started Guide Defining a New Video Conference Defining a New Video Entry QueueTo define a new Video Entry Queue Target Conferences area SIP Factories list Setting an Entry Queue as DefaultTo set an Entry Queue as default Creating a Target Conference from an Entry Queue To create a target conference from an Entry QueueCreating an On Going Video Conference To create an On Going ConferenceDefining a New Video Conference Properties Settings dialog box opens Conference On Port Line Rate Minimum Thresholds MGC+50/MGC+100 Getting Started Guide Defining a New Video Conference Defining a New Video Meeting Room To define a New Video Meeting RoomResource Report To view the MCU resourcesColumn Title Description Resources Report Network Resources Resource Report Network Resources Details Resources Report Media Resources Port-Unit Allocation Area Management Tools To list an MCU’s functional modules Listing the Installed CardsExpand the MCU Configuration tree MUX+ Administrator’s Guide, Chapter MCU Faults Report To view the Faults listFaults Fields Field Description Obtaining Additional Information Reset MCUTo reset the MCU