Polycom DOC2231A Connecting and Setting Up the MGC+100/ MGC+50, Connecting to the Power Source

Page 22

Chapter 2 - Hardware Installation

Connecting and Setting Up the MGC+100/ MGC+50

To Connect the MGC+100/ MGC+50 to the network and power source and set up the system the following procedures are performed:

•Connecting the MGC+ unit to the power source (AC inlet)

•Connecting the MGC+ unit to the LAN Network

•Connecting the MGC+ unit to the network(s)

Connecting to the Power Source

You can connect to an AC Inlet power supply at your site. It is important to follow these steps.

The following restrictions apply to the conductors and connectors that may be used to ground the unit when rack mounted:

•When using bare conductors, they must be coated with an appropriate antioxidant compound before crimp connections are made. Tinned, solder-plated or silver-plated connectors do not have to be prepared in this manner.

•The same bolt assemblies should not secure multiple connectors.

•Listed fastening hardware must be compatible with the materials being joined and must be preclude loosening, deterioration and electrochemical corrosion of the hardware and joint materials.

To connect to the AC Inlet:

1.Make sure the power switch is OFF. Insert the power cable into the power connector on the rear panel of the MGC+100 unit.

Main Switch

AC Inlet

2.Insert the power cable into the power source socket.

2-10

Image 22

Contents MGC+50/MGC+100 Getting Started Guide USA Regulatory Notices Singapore Certificate Table of Contents About Conferences Defining a New Audio Conference Page Before You Begin System OverviewNetwork Equipment, Numbers and Addresses Overview of the Getting Started Guide Defining a New Video Conference Defining a New Audio ConferenceManagement Tools Hardware Installation Inspecting the MGC+/ReadiManager IAM Package Contents MGC+100 Hardware InstallationSystem Safety General Safety PrecautionsRack Mount Safety Precautions Polycom MGC+/ReadiManager PrecautionsUnpacking and Positioning the MGC+100 MGC+100 packageUnpacking the MGC+100 Mounting the MGC+100 in a 23 Rack Unpacking and Positioning the MGC+50 MGC+50 Hardware InstallationTo unpack and position the MGC+50 Unpacking the MGC+50 To install and mount the MGC+50 Mounting the MGC+50 on a RackConnecting to the Power Source Connecting and Setting Up the MGC+100/ MGC+50To connect to the AC Inlet Connecting the MGC+100/MGC+50 to the Local Network Connecting the MGC+ to the Conferencing NetworkTo connect the MGC+ to the Isdn network or T1-CAS Network Isdn network connectionConnecting the MGC+ to the IP Network Using the Compact Flash Disk with the LAN.CFG File First Entry MGC+ Control Unit CU IP ConfigurationTo update the LAN.cfg File Press 1, to Change the MGC+ IP Settings Option DescriptionHardware Installation MGC+50/MGC+100 Getting Started Guide Option Description Using a Keyboard and Monitor Attached to the MGC+ unit MCU Properties dialog box opensType C\\mcu\cfgedit lan.cfg and press Enter MGC+ Software Installation and Configuration Initial ReadiManager IAM ConfigurationInstalling the MGC Manager To install the MGC Manager softwareMGC+ Software Installation and Configuration Starting the MGC Manager Application To start the MGC Manager applicationDefining the MCU To define an MCU ConnectionMGC+50/MGC+100 Getting Started Guide Connecting to an MCU To connect the operator workstation to an MCUIsdn Network Service Configuring the Network ServicesIP Network Service To define the Network Service Define the following parameters To configure a specific IP+ card DNS SIP To configure an Isdn Network Service Click OK Confirmation message is displayed Icon Description About Conferences On-Demand Reservation-less ConferencingScheduled Conferences Meeting RoomsVideo Conference Attributes Entry Queue Default Reservation Templates Reservation TemplatesStarting a Conference Reservations Database window opensBasic Operations Viewing the Conference Dial-in Properties ISDN/PSTN Participants Connecting to a Conference/Entry QueueDialing-in to a Conference/Entry Queue ParticipantsSIP participants Monitoring On Going Conferences General MonitoringExpand the On Going Conferences tree Participant Monitoring Filter dialog box opens Filtering Option DescriptionTo view the list of participants in the Browser pane Expand the On Going Conferences or Reservations treeTo list the participants in the Status pane Participant Level Monitoring To check the properties of a participantOperations Performed During On Going Conferences Adding a Participant to a ConferenceTo add a new participant to a Conference Properties Identification dialog box opensBasic Operations To add a pre-defined participant to a conference Conference Properties dialog box opensBasic Operations Making Dial-Out Connections To manually establish a Dial-out connectionDisconnecting Participants To disconnect a participantMuting a Participant To delete a participantManager User’s Guide, Volume I, Chapter To mute a participant using MGC ManagerLocking and Unlocking a Conference To Lock or Unlock a conference To change the duration of an On Going Conference To terminate a conference manually Changing the Layout in a Continuous Presence Conference Conference Properties Video Sources dialog box opensMGC+50/MGC+100 Getting Started Guide Defining a New Audio Only Entry Queue To define a new Audio Only Entry QueueEntry Queue Properties dialog box opens Defining a New Audio Conference MGC+50/MGC+100 Getting Started Guide To define a new On Going Audio Conference Defining an On Going Audio ConferenceConference Properties General dialog box opens MGC+50/MGC+100 Getting Started Guide Properties Settings dialog box opens MGC+50/MGC+100 Getting Started Guide To define a New Meeting Room Defining a New Audio Only Meeting RoomConference Properties Participants tab is displayed Click the Meet Me Per Conf tab Properties Meet Me Per Conf dialog box opensDefining a New Audio Conference MGC+50/MGC+100 Getting Started Guide Defining a New Video Conference Defining a New Video Entry QueueTo define a new Video Entry Queue Target Conferences area To set an Entry Queue as default Setting an Entry Queue as DefaultSIP Factories list Creating a Target Conference from an Entry Queue To create a target conference from an Entry QueueCreating an On Going Video Conference To create an On Going ConferenceDefining a New Video Conference Properties Settings dialog box opens Conference On Port Line Rate Minimum Thresholds MGC+50/MGC+100 Getting Started Guide Defining a New Video Conference Defining a New Video Meeting Room To define a New Video Meeting RoomResource Report To view the MCU resourcesColumn Title Description Resources Report Network Resources Resource Report Network Resources Details Resources Report Media Resources Port-Unit Allocation Area Management Tools Expand the MCU Configuration tree Listing the Installed CardsTo list an MCU’s functional modules MUX+ Administrator’s Guide, Chapter MCU Faults Report To view the Faults listFaults Fields Field Description To reset the MCU Reset MCUObtaining Additional Information