TP-Link manual TD-W8910GB54M Wireless ADSL2+ Router User Guide

Page 44

TD-W8910GB54M Wireless ADSL2+ Router User Guide

Figure 4-25

2.Enter the Filter name for the rule, it is exclusive and must be filled.

3.Select the protocol: TCP/UDP, TCP, UDP or ICMP in the drop-down list for the connection between the Source IP address and Destination IP address.

4.Enter a Source IP Address in dotted-decimal notation format and then type the Source Subnet Mask and Source Port (port or port: port) in the text boxes separately.

5.Enter a Destination IP Address in dotted-decimal notation format and then type the Destination Subnet Mask and Destination Port (port or port: port) in the text boxes separately.

6.Click the Save/Apply button to save this entry.

)Note:

When you add an Outgoing IP Filtering entry, you must configure at least one condition on the screen above except the Filter name. If you leave the Protocol blank, it means that the rule is effective to all protocols, if you leave the Source IP Address and/or Destination IP Address blank, it suggests that all Source IP Addresses and/or Destination IP Addresses are controlled by the rule, if you leave the Source Port and/or Destination Port blank, it suggests that all Source Ports and/or Destination Ports are controlled by the rule.

IP Filtering - Incoming

Choose “Advanced Setup”Æ“Security”Æ“IP Filtering”Æ“Incoming”, you can configure

Incoming Filtering rules on the screen (shown in Figure 4-26).

The Incoming IP Filtering feature allows some IP traffic from WAN to access some local addresses. By default, all incoming IP traffic from the WAN is blocked when the firewall is enabled. However, some IP traffic can be ACCEPTED by setting up filters.

37

Image 44
Contents TD-W8910GB 54M Wireless ADSL2+ Router Copyright & Trademarks FCC RF Radiation Exposure Statement CE Mark WarningNational Restrictions 2400.0-2483.5 MHz Country Restriction Reason/remarkPackage Contents Contents TD-W8910GB Appendix aAppendix B Main Features WirelessProduct Overview Overview of the RouterSupporting Protocol Transmit Data-rateHardware Installation Guide Front PanelLED Explanation Back PanelInstallation Environment Requirements System RequirementsConnecting the Router Best Location for Wireless Network ConnectionWired network connection Connect Adsl LineHub or Switch to Router Connection Computer to Router ConnectionQuick Installation Guide Configure PCTD-W8910GB54M Wireless ADSL2+ Router User Guide TD-W8910GB54M Wireless ADSL2+ Router User Guide If the TCP/IP configuration for your PC is correct? Configure the Router TD-W8910GB54M Wireless ADSL2+ Router User Guide TD-W8910GB54M Wireless ADSL2+ Router User Guide TD-W8910GB54M Wireless ADSL2+ Router User Guide Basic Router Configuration LoginDevice Info 1 WAN Quick SetupAdvanced Setup Follow the instructions below to Add or Edit an ATM PVC TD-W8910GB54M Wireless ADSL2+ Router User Guide Configuration will be described in 5.4.5 Quality of Service 4to configure them again PPPoATD-W8910GB54M Wireless ADSL2+ Router User Guide PPPoE MERTD-W8910GB54M Wireless ADSL2+ Router User Guide IPoA Bridge 2 LAN TD-W8910GB54M Wireless ADSL2+ Router User Guide MAC Clone 4 NAT Virtual ServersTo setup a virtual server entry TD-W8910GB54M Wireless ADSL2+ Router User Guide Port Triggering To add a new Port TriggeringDMZ Host ALG SecurityTo add a new DMZ Host Setup an Outgoing IP Filtering rule IP FilteringTD-W8910GB54M Wireless ADSL2+ Router User Guide Setup an Incoming IP Filtering rule To setup a MAC Filtering rule MAC FilteringTo setup a Parental Control rule Parental ControlQuality of Service TD-W8910GB54M Wireless ADSL2+ Router User Guide Routing Static Route To add static routing entriesTo remove a static routing entry RIP8 DNS DNS ServerTo setup DDNS, follow these instructions Dynamic DNS9 DSL Port Mapping TD-W8910GB54M Wireless ADSL2+ Router User Guide Wireless LAN Configuration Wireless BasicWireless Security WEP EncryptionConfigure WEP Encryption WPA Configure WPA settings Configure WPA-PSK settings WPA-PSKWPA2 WPA2-PSK Mixed WPA2/WPAWireless -- MAC Filter Mixed WPA2/WPA-PSKWireless Advanced Form of MAC Address must be xxxxxxxxxxxx, like 00130A55FF09TD-W8910GB54M Wireless ADSL2+ Router User Guide Diagnostics Wireless StatisticsSettings BackupTo back up the Router’s current settings ManagementUpdate To update the Router’s settings System LogTo Configure the System Log Settings To View the System LogInternet Time 4 TR-069 client To set the Router’s timeRPC- Remote Procedure Calls Access Control ServicesPasswords To add the IP AddressUpdate Software To change the passwordReboot To update the Routers softwareAppendix a Glossary TD-W8910GB54M Wireless ADSL2+ Router User Guide TD-W8910GB54M Wireless ADSL2+ Router User Guide TD-W8910GB54M Wireless ADSL2+ Router User Guide Appendix B Specifications LED LAN/WAN