TP-Link manual TD-W8910GB54M Wireless ADSL2+ Router User Guide

Page 35

TD-W8910GB54M Wireless ADSL2+ Router User Guide

¾DHCP Server: These settings allow you to configure the Router‘s Dynamic Host Configuration Protocol (DHCP) server function. The DHCP server is enabled by default for the Router’s Ethernet LAN interface. DHCP service will supply IP settings to computers which are configured to automatically obtain IP settings that are connected to the Router though the Ethernet port. When the Router is set for DHCP, it becomes the default gateway for DHCP client connected to it. Keep in mind that if you change the IP address of the Router, you must change the range of IP addresses in the pool used for DHCP on the LAN.

„Start IP Address: Enter a value for the DHCP server to start with when issuing IP addresses. Because the default IP address for the Router is 192.168.1.1, the default Start IP Address is 192.168.1.2, and the Start IP Address must be 192.168.1.2 or greater, but smaller than 192.168.1.254.

„End IP Address: Enter a value for the DHCP server to end with when issuing IP addresses. The End IP Address must be smaller than 192.168.1.254. The default End IP Address is 192.168.1.254.

„Leased Time (hour): The Leased Time is the amount of time in which a network user will be allowed connection to the Router with their current dynamic IP address. Enter the amount of time, in hours, then the user will be “leased” this dynamic IP address. After the dynamic IP address has expired, the user will be automatically assigned a new dynamic IP address. The default is 24 hours.

¾Configure the second IP Address and Subnet Mask: You can configure the Router’s second IP Address and Subnet Mask for LAN Interface though which you can also access to the Web-based Utility as the default IP Address and Subnet Mask.

)Note:

UPnP, DHCP Server and the second IP Address are not available for the connection type of Bridge here, they won’t display on the screen above since only Bridge is selected.

¾Set Address Reservation: When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses should be assigned to servers that require permanent IP settings.

To setup an Address Reservation entry:

1.Click the Set Address Reservation button, and the Address Reservation screen pop up, as it showed below ;

2.Click New Entry button to add new entries, and the screen showed below pop up, you can modify an address reservation entry in this screen;

28

Image 35
Contents TD-W8910GB 54M Wireless ADSL2+ Router Copyright & Trademarks CE Mark Warning FCC RF Radiation Exposure Statement2400.0-2483.5 MHz Country Restriction Reason/remark National RestrictionsPackage Contents Contents TD-W8910GB Appendix aAppendix B Overview of the Router Main FeaturesWireless Product OverviewTransmit Data-rate Supporting ProtocolBack Panel Hardware Installation GuideFront Panel LED ExplanationSystem Requirements Installation Environment RequirementsConnect Adsl Line Connecting the RouterBest Location for Wireless Network Connection Wired network connectionComputer to Router Connection Hub or Switch to Router ConnectionConfigure PC Quick Installation GuideTD-W8910GB54M Wireless ADSL2+ Router User Guide TD-W8910GB54M Wireless ADSL2+ Router User Guide If the TCP/IP configuration for your PC is correct? Configure the Router TD-W8910GB54M Wireless ADSL2+ Router User Guide TD-W8910GB54M Wireless ADSL2+ Router User Guide TD-W8910GB54M Wireless ADSL2+ Router User Guide Login Basic Router ConfigurationDevice Info 1 WAN Quick SetupAdvanced Setup Follow the instructions below to Add or Edit an ATM PVC TD-W8910GB54M Wireless ADSL2+ Router User Guide Configuration will be described in 5.4.5 Quality of Service PPPoA 4to configure them againTD-W8910GB54M Wireless ADSL2+ Router User Guide MER PPPoETD-W8910GB54M Wireless ADSL2+ Router User Guide IPoA Bridge 2 LAN TD-W8910GB54M Wireless ADSL2+ Router User Guide MAC Clone Virtual Servers 4 NATTo setup a virtual server entry TD-W8910GB54M Wireless ADSL2+ Router User Guide To add a new Port Triggering Port TriggeringDMZ Host ALG SecurityTo add a new DMZ Host IP Filtering Setup an Outgoing IP Filtering ruleTD-W8910GB54M Wireless ADSL2+ Router User Guide Setup an Incoming IP Filtering rule MAC Filtering To setup a MAC Filtering ruleParental Control To setup a Parental Control ruleQuality of Service TD-W8910GB54M Wireless ADSL2+ Router User Guide Routing To add static routing entries Static RouteRIP To remove a static routing entryDNS Server 8 DNSDynamic DNS To setup DDNS, follow these instructions9 DSL Port Mapping TD-W8910GB54M Wireless ADSL2+ Router User Guide Wireless Basic Wireless LAN ConfigurationWEP Encryption Wireless SecurityConfigure WEP Encryption WPA Configure WPA settings WPA-PSK Configure WPA-PSK settingsWPA2 Mixed WPA2/WPA WPA2-PSKMixed WPA2/WPA-PSK Wireless -- MAC FilterForm of MAC Address must be xxxxxxxxxxxx, like 00130A55FF09 Wireless AdvancedTD-W8910GB54M Wireless ADSL2+ Router User Guide Wireless Statistics DiagnosticsManagement SettingsBackup To back up the Router’s current settingsUpdate System Log To update the Router’s settingsTo View the System Log To Configure the System Log SettingsInternet Time To set the Router’s time 4 TR-069 clientRPC- Remote Procedure Calls Services Access ControlTo add the IP Address PasswordsTo change the password Update SoftwareTo update the Routers software RebootAppendix a Glossary TD-W8910GB54M Wireless ADSL2+ Router User Guide TD-W8910GB54M Wireless ADSL2+ Router User Guide TD-W8910GB54M Wireless ADSL2+ Router User Guide LED LAN/WAN Appendix B Specifications