TP-Link manual Conventions, TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide

Page 11

TD-W8901N150Mbps Wireless N ADSL2+ Modem Router User Guide

¾Supports long transfers, the max line length can reach to 6.5Km.

¾Supports remote configuration and management through SNMP and CWMP.

¾Supports PPPoE, it allows connecting the internet on demand and disconnecting from the Internet when idle.

¾Provides reliable ESD and surge-protect function with quick response semi-conductive surge protection circuit.

¾High speed and asymmetrical data transmit mode, provides safe and exclusive bandwidth.

¾Supports All ADSL industrial standards.

¾Compatible with all mainstream DSLAM (CO).

¾Provides integrated access of internet and route function which face to SOHO user.

¾Real-time Configuration and device monitoring.

¾Supports Multiple PVC (Permanent Virtual Circuit).

¾Built-in DHCP server.

¾Built-in firewall, supporting IP/MAC filter, Application filter and URL filter.

¾Supports Virtual Server, DMZ host and IP Address Mapping.

¾Supports Dynamic DNS, UPnP and Static Routing.

¾Supports system log and flow Statistics.

¾Supports firmware upgrade and Web management.

¾Provides WPA-PSK/WPA2-PSK data security, TKIP/AES encryption security.

¾Provides 64/128-bit WEP encryption security and wireless LAN ACL (Access Control List).

1.3Conventions

The Router or device mentioned in this User Guide stands for TD-W8901N without any explanations.

Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation.

3

Image 11

Contents Rev 1.0.1 TD-W8901N 150Mbps Wireless N ADSL2+ Modem RouterCOPYRIGHT & TRADEMARKS CE Mark Warning FCC STATEMENTFCC RF Radiation Exposure Statement NCC Notice Canadian Compliance StatementIndustry Canada Statement Korea Warning StatementsSafety Information ETSI EN 300 328 V1.7.1 DECLARATION OF CONFORMITYThe product carries the CE Mark Shennan Rd, Nanshan, Shenzhen, ChinaSoftware Configuration Package ContentsHardware Installation Chapter 3. Quick Installation GuideMaintenance Appendix A SpecificationsAppendix B Troubleshooting Appendix C Technical SupportTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Package Contents1.1 Product Overview 1.2 Main FeaturesWireless Chapter 1.Introduction1.3 Conventions Name Chapter 2.Hardware Installation2.1 The Front Panel LED ExplanationTD-W8901N 2.2 The Back Panel150Mbps Wireless N ADSL2+ Modem Router User Guide 2.3 Installation Environment 2.4 Connecting the Modem Router TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 3.1 Configure PC Chapter 3.Quick Installation GuideTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 1 Is the connection between your PC and the Router correct? 3.2 Login2 Is the TCP/IP configuration for your PC correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button Step 5 Configure the rules for the WLAN, and click NEXT Step 6 Click NEXT to finish the Quick Start 4.1.1 Device Info Chapter 4.Software Configuration4.1 Status 4.1.2 System Log Click the SAVE LOG button to save the logs 4.1.3 StatisticsClick the CLEAR LOG button to clear the logs Statistics Table ¾ Select Ethernet, and you will see the statistics table as below¾ Select WLAN, and you will see the statistics table as below 4.2 Quick StartPlease refer to 3.2 Login ¾ Select ADSL, and you will see the statistics table as below4.3.1 Internet 4.3 Interface SetupVirtual Circuit Select the VC number you want to setup, PVC0~PVC7 4.3.1.1 Dynamic IP Address 4.3.1.2 Static IP Address 4.3.1.3 PPPoA/PPPoE 4.3.1.4 Bridge Mode 4.3.2 LANTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide IGMP Snoop Enable the IGMP Snoop function if you need How to assign a static IP address to the client? If you select Disabled, the DHCP function will not take effect 4.3.3 WirelessTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Access point Settings These are the settings of the access point. You can configure the rules to allow wireless-equipped computers and other devices to communicate with a wireless network ¾ Multiple SSIDs Settings These are the settings of the SSID 3 WPA-PSK 1 WEP-64Bits2 WEP-128Bits 5 WPA-PSK/WPA2-PSK 4 WPA2-PSKMethod One 4.3.3.1 WPS Settings1 PBC Method Two 2 PIN code TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.1 Firewall 4.4 Advanced Setup4.4.2 Routing 4.4.3.1 DMZ 4.4.3 NAT4.4.3.2 Virtual Server 4.4.3.3 IP Address Mapping To add a virtual server entryOther operations for the entries as shown in Figure IP Address Mapping is only available for VCs with Multiple IPs 4.4.4 QoSTo add a mapping rule ¾ Summary Click the button to view the configurations of QoS TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 1 Assign VLAN PVID for each Interface 4.4.5 VLAN2 Define VLAN Group 4.4.6 ADSL 4.5.1 ACL 4.5 Access Management4.5.2 Filter 4.5.2.1 IP Filter To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry 4.5.2.2 MAC Filter Step 6 Go to Step 2 to configure the next two rules Block E-mail received by the IP address 192.168.1.7 on your local network Make the PC with IP address 192.168.1.8 unable to visit the website of IP addressTo add a MAC Address filtering entry Select the “MAC” as the Rule Type on the Filter screen show in Figure 4.5.2.4 URL 4.5.2.3 Application FilterTo add a URL filter entry 4.5.4 UPnP 4.5.3 SNMP4.5.5 DDNS 4.5.6 CWMP 4.6.1 Administration 4.6 Maintenance2 PC’s Clock 4.6.2 Time Zone1 NTP Server automatically 3 Manually 4.6.3 FirmwareTo back up the Router’s current settings To upgrade the routers firmware, follow these instructions below3. The router will reboot after the upgrading has been finished Step 2 Save the file as the appointed file shown in Figure To restore the Router’s settingsStep 2 Click the UPGRADE button to complete 4.6.4 SysRestart 4.6.5 Diagnostics4.7 Help TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Physical and Environment Appendix A SpecificationsGeneral For Mac OS Appendix B TroubleshootingT2. What can I do if I don’t know or forget my password? In the Con-figure IPv4 box under TCP/IP, select Using DHCPClick Internet Options For Windows XPSelect Internet Protocol TCP/IP, and then click Properties Select Never dial a connection T4. What can I do if I cannot access the Internet?Technical Support Appendix C Technical Support