TP-Link manual TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide, WPS Settings, 1 PBC

Page 44
4.3.3.1 WPS Settings

TD-W8901N150Mbps Wireless N ADSL2+ Modem Router User Guide

Figure 4-20

4.3.3.1 WPS Settings

¾WPS Settings: WPS can help you to add a new wireless device to an existing network quickly. This section will guide you how to use WPS function.

WPS state: Display the current WPS state.

WPS mode: If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and Router using either Push Button Configuration (PBC) method or PIN method, please select the one you want.

WPS progress: Show the current WPS progress.

Reset to OOB: Use this button to reset the WPS state to “unconfigured”, so that a new key will be created when using WPS function next time.

1)PBC

If the wireless adapter supports Wi-Fi Protected Setup and the Push Button Configuration (PBC) method, you can add it to the network by PBC with the following two methods. Click PBC, you will see the screen as shown below.

Figure 4-21

Method One:

Step 1: Click Start WPS button in Figure 4-21.

Step 2: Press and hold the WPS button of the adapter directly for 2 or 3 seconds.

Step 3: Wait for a while until the next screen appears. Click Finish to complete the WPS configuration.

36

Image 44
Contents TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router Rev 1.0.1COPYRIGHT & TRADEMARKS CE Mark Warning FCC STATEMENTFCC RF Radiation Exposure Statement Canadian Compliance Statement Industry Canada StatementKorea Warning Statements NCC NoticeSafety Information DECLARATION OF CONFORMITY The product carries the CE MarkShennan Rd, Nanshan, Shenzhen, China ETSI EN 300 328 V1.7.1Package Contents Hardware InstallationChapter 3. Quick Installation Guide Software ConfigurationAppendix A Specifications Appendix B TroubleshootingAppendix C Technical Support MaintenancePackage Contents TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide1.2 Main Features WirelessChapter 1.Introduction 1.1 Product Overview1.3 Conventions Chapter 2.Hardware Installation 2.1 The Front PanelLED Explanation NameTD-W8901N 2.2 The Back Panel150Mbps Wireless N ADSL2+ Modem Router User Guide 2.3 Installation Environment 2.4 Connecting the Modem Router TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 3.Quick Installation Guide 3.1 Configure PCTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 1 Is the connection between your PC and the Router correct? 3.2 Login2 Is the TCP/IP configuration for your PC correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button Step 5 Configure the rules for the WLAN, and click NEXT Step 6 Click NEXT to finish the Quick Start 4.1.1 Device Info Chapter 4.Software Configuration4.1 Status 4.1.2 System Log Click the SAVE LOG button to save the logs 4.1.3 StatisticsClick the CLEAR LOG button to clear the logs ¾ Select Ethernet, and you will see the statistics table as below Statistics Table4.2 Quick Start Please refer to 3.2 Login¾ Select ADSL, and you will see the statistics table as below ¾ Select WLAN, and you will see the statistics table as below4.3 Interface Setup 4.3.1 InternetVirtual Circuit Select the VC number you want to setup, PVC0~PVC7 4.3.1.1 Dynamic IP Address 4.3.1.2 Static IP Address 4.3.1.3 PPPoA/PPPoE 4.3.2 LAN 4.3.1.4 Bridge ModeTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide IGMP Snoop Enable the IGMP Snoop function if you need How to assign a static IP address to the client? 4.3.3 Wireless If you select Disabled, the DHCP function will not take effectTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Access point Settings These are the settings of the access point. You can configure the rules to allow wireless-equipped computers and other devices to communicate with a wireless network ¾ Multiple SSIDs Settings These are the settings of the SSID 3 WPA-PSK 1 WEP-64Bits2 WEP-128Bits 4 WPA2-PSK 5 WPA-PSK/WPA2-PSKMethod One 4.3.3.1 WPS Settings1 PBC Method Two 2 PIN code TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4 Advanced Setup 4.4.1 Firewall4.4.2 Routing 4.4.3 NAT 4.4.3.1 DMZ4.4.3.2 Virtual Server 4.4.3.3 IP Address Mapping To add a virtual server entryOther operations for the entries as shown in Figure IP Address Mapping is only available for VCs with Multiple IPs 4.4.4 QoSTo add a mapping rule ¾ Summary Click the button to view the configurations of QoS TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.5 VLAN 1 Assign VLAN PVID for each Interface2 Define VLAN Group 4.4.6 ADSL 4.5 Access Management 4.5.1 ACL4.5.2 Filter 4.5.2.1 IP Filter To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry Step 6 Go to Step 2 to configure the next two rules Block E-mail received by the IP address 192.168.1.7 on your local network Make the PC with IP address 192.168.1.8 unable to visit the website of IP address 4.5.2.2 MAC FilterTo add a MAC Address filtering entry Select the “MAC” as the Rule Type on the Filter screen show in Figure 4.5.2.3 Application Filter 4.5.2.4 URLTo add a URL filter entry 4.5.3 SNMP 4.5.4 UPnP4.5.5 DDNS 4.5.6 CWMP 4.6 Maintenance 4.6.1 Administration2 PC’s Clock 4.6.2 Time Zone1 NTP Server automatically 4.6.3 Firmware 3 ManuallyTo back up the Router’s current settings To upgrade the routers firmware, follow these instructions below3. The router will reboot after the upgrading has been finished Step 2 Save the file as the appointed file shown in Figure To restore the Router’s settingsStep 2 Click the UPGRADE button to complete 4.6.5 Diagnostics 4.6.4 SysRestart4.7 Help TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Physical and Environment Appendix A SpecificationsGeneral Appendix B Troubleshooting T2. What can I do if I don’t know or forget my password?In the Con-figure IPv4 box under TCP/IP, select Using DHCP For Mac OSClick Internet Options For Windows XPSelect Internet Protocol TCP/IP, and then click Properties T4. What can I do if I cannot access the Internet? Select Never dial a connectionAppendix C Technical Support Technical Support