TP-Link manual Firmware, TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide, Manually

Page 75
3)Manually

TD-W8901N150Mbps Wireless N ADSL2+ Modem Router User Guide

Figure 4-50

3)Manually

Select Manually as the Synchronize time, you need to set the date and time corresponding to the current time.

Figure 4-51

4.6.3 Firmware

Choose “Maintenance→Firmware”, you can upgrade the firmware of the Router in the screen (shown in Figure 4-52). Make sure the firmware or romfile you want to use is on the local hard drive of the computer. Click Browse to find the local hard drive and locate the firmware or romfile to be used for upgrade.

67

Page 74 Page 76
Image 75
Page 74 Page 76
Contents Rev 1.0.1 TD-W8901N 150Mbps Wireless N ADSL2+ Modem RouterCOPYRIGHT & TRADEMARKS FCC STATEMENT FCC RF Radiation Exposure StatementCE Mark Warning NCC Notice Canadian Compliance StatementIndustry Canada Statement Korea Warning StatementsSafety Information ETSI EN 300 328 V1.7.1 DECLARATION OF CONFORMITYThe product carries the CE Mark Shennan Rd, Nanshan, Shenzhen, ChinaSoftware Configuration Package ContentsHardware Installation Chapter 3. Quick Installation GuideMaintenance Appendix A SpecificationsAppendix B Troubleshooting Appendix C Technical SupportTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Package Contents1.1 Product Overview 1.2 Main FeaturesWireless Chapter 1.Introduction1.3 Conventions Name Chapter 2.Hardware Installation2.1 The Front Panel LED Explanation2.2 The Back Panel 150Mbps Wireless N ADSL2+ Modem Router User GuideTD-W8901N 2.3 Installation Environment 2.4 Connecting the Modem Router TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 3.1 Configure PC Chapter 3.Quick Installation GuideTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 3.2 Login 2 Is the TCP/IP configuration for your PC correct?1 Is the connection between your PC and the Router correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button Step 5 Configure the rules for the WLAN, and click NEXT Step 6 Click NEXT to finish the Quick Start Chapter 4.Software Configuration 4.1 Status4.1.1 Device Info 4.1.2 System Log 4.1.3 Statistics Click the CLEAR LOG button to clear the logsClick the SAVE LOG button to save the logs Statistics Table ¾ Select Ethernet, and you will see the statistics table as below¾ Select WLAN, and you will see the statistics table as below 4.2 Quick StartPlease refer to 3.2 Login ¾ Select ADSL, and you will see the statistics table as below4.3.1 Internet 4.3 Interface SetupVirtual Circuit Select the VC number you want to setup, PVC0~PVC7 4.3.1.1 Dynamic IP Address 4.3.1.2 Static IP Address 4.3.1.3 PPPoA/PPPoE 4.3.1.4 Bridge Mode 4.3.2 LANTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide IGMP Snoop Enable the IGMP Snoop function if you need How to assign a static IP address to the client? If you select Disabled, the DHCP function will not take effect 4.3.3 WirelessTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Access point Settings These are the settings of the access point. You can configure the rules to allow wireless-equipped computers and other devices to communicate with a wireless network ¾ Multiple SSIDs Settings These are the settings of the SSID 1 WEP-64Bits 2 WEP-128Bits3 WPA-PSK 5 WPA-PSK/WPA2-PSK 4 WPA2-PSK4.3.3.1 WPS Settings 1 PBCMethod One Method Two 2 PIN code TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.1 Firewall 4.4 Advanced Setup4.4.2 Routing 4.4.3.1 DMZ 4.4.3 NAT4.4.3.2 Virtual Server To add a virtual server entry Other operations for the entries as shown in Figure4.4.3.3 IP Address Mapping 4.4.4 QoS To add a mapping ruleIP Address Mapping is only available for VCs with Multiple IPs ¾ Summary Click the button to view the configurations of QoS TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 1 Assign VLAN PVID for each Interface 4.4.5 VLAN2 Define VLAN Group 4.4.6 ADSL 4.5.1 ACL 4.5 Access Management4.5.2 Filter 4.5.2.1 IP Filter To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry 4.5.2.2 MAC Filter Step 6 Go to Step 2 to configure the next two rules Block E-mail received by the IP address 192.168.1.7 on your local network Make the PC with IP address 192.168.1.8 unable to visit the website of IP addressTo add a MAC Address filtering entry Select the “MAC” as the Rule Type on the Filter screen show in Figure 4.5.2.4 URL 4.5.2.3 Application FilterTo add a URL filter entry 4.5.4 UPnP 4.5.3 SNMP4.5.5 DDNS 4.5.6 CWMP 4.6.1 Administration 4.6 Maintenance4.6.2 Time Zone 1 NTP Server automatically2 PC’s Clock 3 Manually 4.6.3 FirmwareTo upgrade the routers firmware, follow these instructions below 3. The router will reboot after the upgrading has been finishedTo back up the Router’s current settings To restore the Router’s settings Step 2 Click the UPGRADE button to completeStep 2 Save the file as the appointed file shown in Figure 4.6.4 SysRestart 4.6.5 Diagnostics4.7 Help TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Appendix A Specifications GeneralPhysical and Environment For Mac OS Appendix B TroubleshootingT2. What can I do if I don’t know or forget my password? In the Con-figure IPv4 box under TCP/IP, select Using DHCPFor Windows XP Select Internet Protocol TCP/IP, and then click PropertiesClick Internet Options Select Never dial a connection T4. What can I do if I cannot access the Internet?Technical Support Appendix C Technical Support
Top Page Image Contents