TP-Link TD-W8901N manual SysRestart, Diagnostics

Page 78

4.6.4 SysRestart

TD-W8901N150Mbps Wireless N ADSL2+ Modem Router User Guide

4.6.4 SysRestart

Choose “Maintenance→SysRestart”, you can select to restart the device with current settings or restore to factory default settings in the screen (shown in Figure 4-55).

Figure 4-55

4.6.5 Diagnostics

Choose “Maintenance→Diagnostics”, you can view the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides in the screen (shown in Figure 4-56).

70

Image 78

Contents TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router Rev 1.0.1COPYRIGHT & TRADEMARKS FCC STATEMENT FCC RF Radiation Exposure StatementCE Mark Warning Korea Warning Statements Canadian Compliance StatementIndustry Canada Statement NCC NoticeSafety Information Shennan Rd, Nanshan, Shenzhen, China DECLARATION OF CONFORMITYThe product carries the CE Mark ETSI EN 300 328 V1.7.1Chapter 3. Quick Installation Guide Package ContentsHardware Installation Software ConfigurationAppendix C Technical Support Appendix A SpecificationsAppendix B Troubleshooting MaintenancePackage Contents TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User GuideChapter 1.Introduction 1.2 Main FeaturesWireless 1.1 Product Overview1.3 Conventions LED Explanation Chapter 2.Hardware Installation2.1 The Front Panel Name2.2 The Back Panel 150Mbps Wireless N ADSL2+ Modem Router User GuideTD-W8901N 2.3 Installation Environment 2.4 Connecting the Modem Router TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 3.Quick Installation Guide 3.1 Configure PCTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 3.2 Login 2 Is the TCP/IP configuration for your PC correct?1 Is the connection between your PC and the Router correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button Step 5 Configure the rules for the WLAN, and click NEXT Step 6 Click NEXT to finish the Quick Start Chapter 4.Software Configuration 4.1 Status4.1.1 Device Info 4.1.2 System Log 4.1.3 Statistics Click the CLEAR LOG button to clear the logsClick the SAVE LOG button to save the logs ¾ Select Ethernet, and you will see the statistics table as below Statistics Table¾ Select ADSL, and you will see the statistics table as below 4.2 Quick StartPlease refer to 3.2 Login ¾ Select WLAN, and you will see the statistics table as below4.3 Interface Setup 4.3.1 InternetVirtual Circuit Select the VC number you want to setup, PVC0~PVC7 4.3.1.1 Dynamic IP Address 4.3.1.2 Static IP Address 4.3.1.3 PPPoA/PPPoE 4.3.2 LAN 4.3.1.4 Bridge ModeTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide IGMP Snoop Enable the IGMP Snoop function if you need How to assign a static IP address to the client? 4.3.3 Wireless If you select Disabled, the DHCP function will not take effectTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Access point Settings These are the settings of the access point. You can configure the rules to allow wireless-equipped computers and other devices to communicate with a wireless network ¾ Multiple SSIDs Settings These are the settings of the SSID 1 WEP-64Bits 2 WEP-128Bits3 WPA-PSK 4 WPA2-PSK 5 WPA-PSK/WPA2-PSK4.3.3.1 WPS Settings 1 PBCMethod One Method Two 2 PIN code TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4 Advanced Setup 4.4.1 Firewall4.4.2 Routing 4.4.3 NAT 4.4.3.1 DMZ4.4.3.2 Virtual Server To add a virtual server entry Other operations for the entries as shown in Figure4.4.3.3 IP Address Mapping 4.4.4 QoS To add a mapping ruleIP Address Mapping is only available for VCs with Multiple IPs ¾ Summary Click the button to view the configurations of QoS TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.5 VLAN 1 Assign VLAN PVID for each Interface2 Define VLAN Group 4.4.6 ADSL 4.5 Access Management 4.5.1 ACL4.5.2 Filter 4.5.2.1 IP Filter To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry Step 6 Go to Step 2 to configure the next two rules Block E-mail received by the IP address 192.168.1.7 on your local network Make the PC with IP address 192.168.1.8 unable to visit the website of IP address 4.5.2.2 MAC FilterTo add a MAC Address filtering entry Select the “MAC” as the Rule Type on the Filter screen show in Figure 4.5.2.3 Application Filter 4.5.2.4 URLTo add a URL filter entry 4.5.3 SNMP 4.5.4 UPnP4.5.5 DDNS 4.5.6 CWMP 4.6 Maintenance 4.6.1 Administration4.6.2 Time Zone 1 NTP Server automatically2 PC’s Clock 4.6.3 Firmware 3 ManuallyTo upgrade the routers firmware, follow these instructions below 3. The router will reboot after the upgrading has been finishedTo back up the Router’s current settings To restore the Router’s settings Step 2 Click the UPGRADE button to completeStep 2 Save the file as the appointed file shown in Figure 4.6.5 Diagnostics 4.6.4 SysRestart4.7 Help TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Appendix A Specifications GeneralPhysical and Environment In the Con-figure IPv4 box under TCP/IP, select Using DHCP Appendix B TroubleshootingT2. What can I do if I don’t know or forget my password? For Mac OSFor Windows XP Select Internet Protocol TCP/IP, and then click PropertiesClick Internet Options T4. What can I do if I cannot access the Internet? Select Never dial a connectionAppendix C Technical Support Technical Support