TP-Link TD-W8901N manual Canadian Compliance Statement, Industry Canada Statement, NCC Notice

Page 4

This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

This device has been designed to operate with the antennas listed below, and having a maximum gain of 5dBi. Antennas not included in this list or having a gain greater than 5dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.

Canadian Compliance Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1)This device may not cause interference, and

(2)This device must accept any interference, including interference that may cause undesired operation of the device.

Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes:

(1)cet appareil ne doit pas provoquer d’interférences et

(2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité de l’appareil.

Industry Canada Statement

Complies with the Canadian ICES-003 Class B specifications.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations.

Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Korea Warning Statements:

당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice:

注意!

依據 低功率電波輻射性電機管理辦法

第十二條 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻 率、加大功率或變更原設計之特性或功能。

III

Image 4
Contents TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router Rev 1.0.1COPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTCE Mark Warning Canadian Compliance Statement Industry Canada StatementKorea Warning Statements NCC NoticeSafety Information DECLARATION OF CONFORMITY The product carries the CE MarkShennan Rd, Nanshan, Shenzhen, China ETSI EN 300 328 V1.7.1Package Contents Hardware InstallationChapter 3. Quick Installation Guide Software ConfigurationAppendix A Specifications Appendix B TroubleshootingAppendix C Technical Support MaintenancePackage Contents TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide1.2 Main Features WirelessChapter 1.Introduction 1.1 Product Overview1.3 Conventions Chapter 2.Hardware Installation 2.1 The Front PanelLED Explanation Name150Mbps Wireless N ADSL2+ Modem Router User Guide 2.2 The Back PanelTD-W8901N 2.3 Installation Environment 2.4 Connecting the Modem Router TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 3.Quick Installation Guide 3.1 Configure PCTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 2 Is the TCP/IP configuration for your PC correct? 3.2 Login1 Is the connection between your PC and the Router correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button Step 5 Configure the rules for the WLAN, and click NEXT Step 6 Click NEXT to finish the Quick Start 4.1 Status Chapter 4.Software Configuration4.1.1 Device Info 4.1.2 System Log Click the CLEAR LOG button to clear the logs 4.1.3 StatisticsClick the SAVE LOG button to save the logs ¾ Select Ethernet, and you will see the statistics table as below Statistics Table4.2 Quick Start Please refer to 3.2 Login¾ Select ADSL, and you will see the statistics table as below ¾ Select WLAN, and you will see the statistics table as below4.3 Interface Setup 4.3.1 InternetVirtual Circuit Select the VC number you want to setup, PVC0~PVC7 4.3.1.1 Dynamic IP Address 4.3.1.2 Static IP Address 4.3.1.3 PPPoA/PPPoE 4.3.2 LAN 4.3.1.4 Bridge ModeTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide IGMP Snoop Enable the IGMP Snoop function if you need How to assign a static IP address to the client? 4.3.3 Wireless If you select Disabled, the DHCP function will not take effectTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Access point Settings These are the settings of the access point. You can configure the rules to allow wireless-equipped computers and other devices to communicate with a wireless network ¾ Multiple SSIDs Settings These are the settings of the SSID 2 WEP-128Bits 1 WEP-64Bits3 WPA-PSK 4 WPA2-PSK 5 WPA-PSK/WPA2-PSK1 PBC 4.3.3.1 WPS SettingsMethod One Method Two 2 PIN code TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4 Advanced Setup 4.4.1 Firewall4.4.2 Routing 4.4.3 NAT 4.4.3.1 DMZ4.4.3.2 Virtual Server Other operations for the entries as shown in Figure To add a virtual server entry4.4.3.3 IP Address Mapping To add a mapping rule 4.4.4 QoSIP Address Mapping is only available for VCs with Multiple IPs ¾ Summary Click the button to view the configurations of QoS TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.5 VLAN 1 Assign VLAN PVID for each Interface2 Define VLAN Group 4.4.6 ADSL 4.5 Access Management 4.5.1 ACL4.5.2 Filter 4.5.2.1 IP Filter To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry Step 6 Go to Step 2 to configure the next two rules Block E-mail received by the IP address 192.168.1.7 on your local network Make the PC with IP address 192.168.1.8 unable to visit the website of IP address 4.5.2.2 MAC FilterTo add a MAC Address filtering entry Select the “MAC” as the Rule Type on the Filter screen show in Figure 4.5.2.3 Application Filter 4.5.2.4 URLTo add a URL filter entry 4.5.3 SNMP 4.5.4 UPnP4.5.5 DDNS 4.5.6 CWMP 4.6 Maintenance 4.6.1 Administration1 NTP Server automatically 4.6.2 Time Zone2 PC’s Clock 4.6.3 Firmware 3 Manually3. The router will reboot after the upgrading has been finished To upgrade the routers firmware, follow these instructions belowTo back up the Router’s current settings Step 2 Click the UPGRADE button to complete To restore the Router’s settingsStep 2 Save the file as the appointed file shown in Figure 4.6.5 Diagnostics 4.6.4 SysRestart4.7 Help TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide General Appendix A SpecificationsPhysical and Environment Appendix B Troubleshooting T2. What can I do if I don’t know or forget my password?In the Con-figure IPv4 box under TCP/IP, select Using DHCP For Mac OSSelect Internet Protocol TCP/IP, and then click Properties For Windows XPClick Internet Options T4. What can I do if I cannot access the Internet? Select Never dial a connectionAppendix C Technical Support Technical Support