TP-Link TD-W8901N manual Interface Setup, Internet

Page 29

4.3Interface Setup

TD-W8901N150Mbps Wireless N ADSL2+ Modem Router User Guide

4.3Interface Setup

Choose “Interface Setup”, you can see the next submenus: Internet, LAN and Wireless.

Figure 4-5

Click any of them, and you will be able to configure the corresponding function.

4.3.1 Internet

Choose “Interface Setup→Internet” menu, you can configure the parameters for WAN ports in the next screen (shown in Figure 4-6).

21

Image 29

Contents Rev 1.0.1 TD-W8901N 150Mbps Wireless N ADSL2+ Modem RouterCOPYRIGHT & TRADEMARKS CE Mark Warning FCC STATEMENTFCC RF Radiation Exposure Statement Industry Canada Statement Canadian Compliance StatementKorea Warning Statements NCC NoticeSafety Information The product carries the CE Mark DECLARATION OF CONFORMITYShennan Rd, Nanshan, Shenzhen, China ETSI EN 300 328 V1.7.1Hardware Installation Package ContentsChapter 3. Quick Installation Guide Software ConfigurationAppendix B Troubleshooting Appendix A SpecificationsAppendix C Technical Support MaintenanceTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Package ContentsWireless 1.2 Main FeaturesChapter 1.Introduction 1.1 Product Overview1.3 Conventions 2.1 The Front Panel Chapter 2.Hardware InstallationLED Explanation NameTD-W8901N 2.2 The Back Panel150Mbps Wireless N ADSL2+ Modem Router User Guide 2.3 Installation Environment 2.4 Connecting the Modem Router TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 3.1 Configure PC Chapter 3.Quick Installation GuideTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 1 Is the connection between your PC and the Router correct? 3.2 Login2 Is the TCP/IP configuration for your PC correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button Step 5 Configure the rules for the WLAN, and click NEXT Step 6 Click NEXT to finish the Quick Start 4.1.1 Device Info Chapter 4.Software Configuration4.1 Status 4.1.2 System Log Click the SAVE LOG button to save the logs 4.1.3 StatisticsClick the CLEAR LOG button to clear the logs Statistics Table ¾ Select Ethernet, and you will see the statistics table as belowPlease refer to 3.2 Login 4.2 Quick Start¾ Select ADSL, and you will see the statistics table as below ¾ Select WLAN, and you will see the statistics table as below4.3.1 Internet 4.3 Interface SetupVirtual Circuit Select the VC number you want to setup, PVC0~PVC7 4.3.1.1 Dynamic IP Address 4.3.1.2 Static IP Address 4.3.1.3 PPPoA/PPPoE 4.3.1.4 Bridge Mode 4.3.2 LANTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide IGMP Snoop Enable the IGMP Snoop function if you need How to assign a static IP address to the client? If you select Disabled, the DHCP function will not take effect 4.3.3 WirelessTD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Access point Settings These are the settings of the access point. You can configure the rules to allow wireless-equipped computers and other devices to communicate with a wireless network ¾ Multiple SSIDs Settings These are the settings of the SSID 3 WPA-PSK 1 WEP-64Bits2 WEP-128Bits 5 WPA-PSK/WPA2-PSK 4 WPA2-PSKMethod One 4.3.3.1 WPS Settings1 PBC Method Two 2 PIN code TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.1 Firewall 4.4 Advanced Setup4.4.2 Routing 4.4.3.1 DMZ 4.4.3 NAT4.4.3.2 Virtual Server 4.4.3.3 IP Address Mapping To add a virtual server entryOther operations for the entries as shown in Figure IP Address Mapping is only available for VCs with Multiple IPs 4.4.4 QoSTo add a mapping rule ¾ Summary Click the button to view the configurations of QoS TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 1 Assign VLAN PVID for each Interface 4.4.5 VLAN2 Define VLAN Group 4.4.6 ADSL 4.5.1 ACL 4.5 Access Management4.5.2 Filter 4.5.2.1 IP Filter To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry 4.5.2.2 MAC Filter Step 6 Go to Step 2 to configure the next two rules Block E-mail received by the IP address 192.168.1.7 on your local network Make the PC with IP address 192.168.1.8 unable to visit the website of IP addressTo add a MAC Address filtering entry Select the “MAC” as the Rule Type on the Filter screen show in Figure 4.5.2.4 URL 4.5.2.3 Application FilterTo add a URL filter entry 4.5.4 UPnP 4.5.3 SNMP4.5.5 DDNS 4.5.6 CWMP 4.6.1 Administration 4.6 Maintenance2 PC’s Clock 4.6.2 Time Zone1 NTP Server automatically 3 Manually 4.6.3 FirmwareTo back up the Router’s current settings To upgrade the routers firmware, follow these instructions below3. The router will reboot after the upgrading has been finished Step 2 Save the file as the appointed file shown in Figure To restore the Router’s settingsStep 2 Click the UPGRADE button to complete 4.6.4 SysRestart 4.6.5 Diagnostics4.7 Help TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Physical and Environment Appendix A SpecificationsGeneral T2. What can I do if I don’t know or forget my password? Appendix B TroubleshootingIn the Con-figure IPv4 box under TCP/IP, select Using DHCP For Mac OSClick Internet Options For Windows XPSelect Internet Protocol TCP/IP, and then click Properties Select Never dial a connection T4. What can I do if I cannot access the Internet?Technical Support Appendix C Technical Support