Delta DVPEN01-SL operation manual Explanations on CR, E-mail Functions

Page 10

Ethernet Communication Module DVPEN01-SL

		CR#			Attribute	Content	Explanation
		HW		LW	Attribute	Content	Explanation
		HW		LW
			#115		R/W	Modbus TCP trigger	Setting up whether to send out data in Modbus TCP mode

			#116		R/W	Modbus TCP status	Displaying current status of Modbus TCP mode

	#118		#117		R/W	Modbus TCP	Setting up destination IP address for Modbus TCP transaction
	#118		#117		R/W	destination IP
						destination IP
			#119		R/W	Modbus TCP data length	Setting up the data length for Modbus TCP transaction

	#219 ~ #120				R/W	Modbus TCP data buffer	Data buffer of Modbus TCP for storing sending/receiving data

	#248 ~ #220				-	Reserved

				#251	R	Error code	Displaying the errors. See table of error codes in the following
				#251	R	Error code	section for more information.
							section for more information.
	#255 ~ #252				-	Reserved

Symbols “R” refers to “able to read data by FROM instrcution”; “W” refers to “able to write data by TO instrcution”.

4.2Explanations on CR

CR#0: Model Name

Explanations:

1.Model code of DVPEN01-SL = H’4050.

2.You can read the model code in the program to see if the I/O module exists.

CR#1: Firmware Version

Explanations:

The firmware version of DVPEN01-SL is displayed in hex, e.g. H’0100 indicates version V1.00.

CR#2: Communication Mode

Explanations:

Bit No.	Mode	“0”	“1”
b0	Modbus TCP	Disable	Enable

b1	Data exchange	Disable	Enable

E-mail Functions

CR#3 ~ 6: E-Mail Event 1 ~ 4 Trigger

Explanations:

When the CR is set as “1”, E-mail sending will be enabled. After the sending is completed, the CR will automatically be reset as “0”. Note: Please trigger by differential instructions.

8	DVP-PLC Operation Manual

Image 10

Contents DVPEN01-SL Page Table of Contents Application Examples Specifications FunctionsDimension Product ProfilesInstallation LED IndicatorsRJ-45 PIN Definition Control Register CR Control Registers in DVPEN01-SLEthernet Communication Module DVPEN01-SL Explanations on CR „ E-mail Functions„ Data Exchange Ethernet Communication Module DVPEN01-SL „ Sending Modbus TCP Instruction Ethernet Communication Module DVPEN01-SL Numbering of Left-Side Modules „ RTU MappingSetting up Communication & Searching for Modules „ Communication settings„ Broadcast search „ Designating model to search Ethernet Communication Module DVPEN01-SL „ Searching by IP address „ Opening DVPEN01-SL setup page by RS-232 Basic Settings „ Setting up DVPEN01-SL basicsNetwork Settings „ Setting up static IP of the PCEthernet Communication Module DVPEN01-SL „ Setting up DVPEN01-SL Network DhcpSetting up E-Mails „ Setting up DVPEN01-SL mail„ Setting up DVPEN01-SL data exchange Data Exchange„ The settings RTUIP Filter „ Setting up IP filterStatic ARP Table „ Setting up static ARP table Setting up Password„ Setting up DVPEN01-SL password Returning to Default Setting „ DVPEN01-SL returning to default settingSetting up IP and Communicating through WPLSoft Application ExamplesEthernet Communication Module DVPEN01-SL Open Basic setup Switch to Network setup Connecting the PC with DVPEN01-SL through LAN DVPEN01 DVP-PLC Ethernet Communication Module DVPEN01-SL Ethernet Communication Module DVPEN01-SL Setting up Password and Clearing Password Ethernet Communication Module DVPEN01-SL After the password is cleared, you can modify the parameters IP Filter Protection Ethernet Communication Module DVPEN01-SL Setting up Static ARP Table Ethernet Communication Module DVPEN01-SL Application of E-Mail Application of Data Exchange ExplanationsEthernet Communication Module DVPEN01-SL TRD Application of Data Exchange Ethernet Communication Module DVPEN01-SL Ethernet Communication Module DVPEN01-SL From Explanations Data exchange will be executed every one second Application of Modbus TCP Master RTU Mapping Ethernet Communication Module DVPEN01-SL Ethernet Communication Module DVPEN01-SL