Delta DVPEN01-SL operation manual LED Indicators, RJ-45 PIN Definition, Installation

Page 7

Ethernet Communication Module DVPEN01-SL

2.3LED Indicators

Indicator	Color	Indication
POWER	Green	Power indication

RS-232	Red	Communication status of the series port

100M	Orange	Network connection status

LINK	Green	Network communication speed

2.4RJ-45 PIN Definition

RJ-45 sketch	Terminal No.	Definition	Explanation

	1	Tx+	Positive pole for data transmission

	2	Tx-	Negative pole for data transmission

	3	Rx+	Positive pole for data receiving

	6	Rx-	Negative pole for data receiving

	4, 5, 7, 8	-	N/C

3 Installation & Wiring

This section gives instructions on how to connect DVPEN01-SL with PLC MPU and how to connect DVPEN01-SL to the network.

3.1Installation

Connect PLC MPU to DVPEN01-SL

zAdjust the I/O module clip on the left side of the MPU.

zMeet the I/O module port of the MPU with DVPEN01-SL as shown in the figure below.

zFasten the I/O module clip on the left side of the MPU.

DVPEN01	DVP28SV
POWER
RS-232
100M
LINK
	RS-232

LAN

Connect DVPEN01-SL to other I/O modules

zTo connect DVPEN01-SL with the other I/O module, lift the extension clip of the I/O module by a screwdriver and open the side cover.

DVP-PLC Operation Manual

5

Image 7

Contents DVPEN01-SL Page Table of Contents Application Examples Functions SpecificationsProduct Profiles DimensionInstallation LED IndicatorsRJ-45 PIN Definition Control Registers in DVPEN01-SL Control Register CREthernet Communication Module DVPEN01-SL „ E-mail Functions Explanations on CR„ Data Exchange Ethernet Communication Module DVPEN01-SL „ Sending Modbus TCP Instruction Ethernet Communication Module DVPEN01-SL „ RTU Mapping Numbering of Left-Side Modules„ Communication settings Setting up Communication & Searching for Modules„ Broadcast search „ Designating model to search Ethernet Communication Module DVPEN01-SL „ Searching by IP address „ Opening DVPEN01-SL setup page by RS-232 „ Setting up DVPEN01-SL basics Basic Settings„ Setting up static IP of the PC Network SettingsEthernet Communication Module DVPEN01-SL Dhcp „ Setting up DVPEN01-SL Network„ Setting up DVPEN01-SL mail Setting up E-MailsData Exchange „ Setting up DVPEN01-SL data exchangeRTU „ The settingsIP Filter „ Setting up IP filterStatic ARP Table „ Setting up static ARP table Setting up Password„ Setting up DVPEN01-SL password „ DVPEN01-SL returning to default setting Returning to Default SettingApplication Examples Setting up IP and Communicating through WPLSoftEthernet Communication Module DVPEN01-SL Open Basic setup Switch to Network setup Connecting the PC with DVPEN01-SL through LAN DVPEN01 DVP-PLC Ethernet Communication Module DVPEN01-SL Ethernet Communication Module DVPEN01-SL Setting up Password and Clearing Password Ethernet Communication Module DVPEN01-SL After the password is cleared, you can modify the parameters IP Filter Protection Ethernet Communication Module DVPEN01-SL Setting up Static ARP Table Ethernet Communication Module DVPEN01-SL Application of E-Mail Explanations Application of Data ExchangeEthernet Communication Module DVPEN01-SL TRD Application of Data Exchange Ethernet Communication Module DVPEN01-SL Ethernet Communication Module DVPEN01-SL From Explanations Data exchange will be executed every one second Application of Modbus TCP Master RTU Mapping Ethernet Communication Module DVPEN01-SL Ethernet Communication Module DVPEN01-SL