Delta DVPEN01-SL operation manual Table of Contents

Page 3

Ethernet Communication Module DVPEN01-SL

Warning

3Please read this instruction carefully before use and follow this instruction to operate the device in order to prevent damages on the device or injuries to staff.

3Switch off the power before wiring.

3RTU-DNET is an OPEN TYPE device and therefore should be installed in an enclosure free of airborne dust, humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key or specific tools are required for operating the enclosure) in case danger and damage on the device may occur.

3RTU-DNET is to be used for controlling the operating machine and equipment. In order not to damage it, only qualified professional staff familiar with the structure and operation of RTU-DNET can install, operate, wire and maintain it.

3DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur. Check all the wirings again before switching on the power and DO NOT touch any terminal when the power is switched on. Make sure the ground terminal is correctly grounded in order to prevent electromagnetic interference.

Table of Contents

1	INTRODUCTION		3
	1.1	Functions	3
	1.2	Specifications	3
2	PRODUCT PROFILE & OUTLINE		4
	2.1	Dimension	4
	2.2	Product Profiles	4
	2.3	LED Indicators	5
	2.4	RJ-45 PIN Definition	5
3	INSTALLATION & WIRING		5
	3.1	Installation	5
4	CONTROL REGISTER (CR)		6
	4.1	Control Registers in DVPEN01-SL	6
	4.2	Explanations on CR	8
	4.3	Numbering of Left-Side Modules	13
5	SETTING UP SOFTWARE		14
	5.1	Setting up Communication & Searching for Modules	14
	5.2	Basic Settings	20
	5.3	Network Settings	21
	5.4	Setting up E-Mails	24
	5.5	Data Exchange	25
	5.6	RTU	26
	5.7	IP Filter	27
	5.8	Static ARP Table	27
	5.9	Setting up Password	28

DVP-PLC Operation Manual

1

Image 3

Contents DVPEN01-SL Page Table of Contents Application Examples Functions SpecificationsProduct Profiles DimensionLED Indicators InstallationRJ-45 PIN Definition Control Registers in DVPEN01-SL Control Register CREthernet Communication Module DVPEN01-SL „ E-mail Functions Explanations on CR„ Data Exchange Ethernet Communication Module DVPEN01-SL „ Sending Modbus TCP Instruction Ethernet Communication Module DVPEN01-SL „ RTU Mapping Numbering of Left-Side Modules„ Communication settings Setting up Communication & Searching for Modules„ Broadcast search „ Designating model to search Ethernet Communication Module DVPEN01-SL „ Searching by IP address „ Opening DVPEN01-SL setup page by RS-232 „ Setting up DVPEN01-SL basics Basic Settings„ Setting up static IP of the PC Network SettingsEthernet Communication Module DVPEN01-SL Dhcp „ Setting up DVPEN01-SL Network„ Setting up DVPEN01-SL mail Setting up E-MailsData Exchange „ Setting up DVPEN01-SL data exchangeRTU „ The settings„ Setting up IP filter IP FilterStatic ARP Table Setting up Password „ Setting up static ARP table„ Setting up DVPEN01-SL password „ DVPEN01-SL returning to default setting Returning to Default SettingApplication Examples Setting up IP and Communicating through WPLSoftEthernet Communication Module DVPEN01-SL Open Basic setup Switch to Network setup Connecting the PC with DVPEN01-SL through LAN DVPEN01 DVP-PLC Ethernet Communication Module DVPEN01-SL Ethernet Communication Module DVPEN01-SL Setting up Password and Clearing Password Ethernet Communication Module DVPEN01-SL After the password is cleared, you can modify the parameters IP Filter Protection Ethernet Communication Module DVPEN01-SL Setting up Static ARP Table Ethernet Communication Module DVPEN01-SL Application of E-Mail Explanations Application of Data ExchangeEthernet Communication Module DVPEN01-SL TRD Application of Data Exchange Ethernet Communication Module DVPEN01-SL Ethernet Communication Module DVPEN01-SL From Explanations Data exchange will be executed every one second Application of Modbus TCP Master RTU Mapping Ethernet Communication Module DVPEN01-SL Ethernet Communication Module DVPEN01-SL