Delta DVPEN01-SL operation manual From

Page 53

Ethernet Communication Module DVPEN01-SL

M1000			TRD	D100
			TRD	D100
M1013	M2	M1	SET	M1
			SET	M1
M1			TOP	K100	K28	K0	K1
			TOP	K100	K28	K0	K1
			TOP	K100	K26	HC0A8	K1
			TOP	K100	K25	H4	K1
			TOP	K100	K29	D100	K7
			TOP	K100	K14	K0	K1
			TOP	K100	K13	K1	K1
			SET	M2
			RST	M1
M2
			FROM	K100	K14	D14	K1
	= D14 K2		RST	M2
	= D14 K3		RST	M2
			END
Explanations:

•The data exchange will be executed every one second.

•Write “0” into CR#28, and PLC_B will use CR#25 ~ CR#26 as the IP address of the destination PLC.

•Write the IP address of PLC_A into CR#25 and CR#26. The first two IP codes (192.168 = H’C0A8) should be written into CR#26, and the last two IP codes (0.4 = H’0004) into CR#25.

•Write the data in RTC into CR#29 ~ CR#35.

•Write “1” into CR#13 to start the data exchange.

•CR#14 = 2 refers to successful execution. CR#14 = 3 refers to failed execution.

2.Compile the ladder diagram for PLC_A and download it to PLC_A.

M1013
FROM	K100	K49	D0	K7
END
Explanations:

•The received data are stored in CR#49 ~ CR#55.

•The data received every one second are written into D0 ~ D6.

DVP-PLC Operation Manual

51

Image 53

Contents DVPEN01-SL Page Table of Contents Application Examples Functions SpecificationsProduct Profiles DimensionRJ-45 PIN Definition LED IndicatorsInstallation Control Registers in DVPEN01-SL Control Register CREthernet Communication Module DVPEN01-SL „ E-mail Functions Explanations on CR„ Data Exchange Ethernet Communication Module DVPEN01-SL „ Sending Modbus TCP Instruction Ethernet Communication Module DVPEN01-SL „ RTU Mapping Numbering of Left-Side Modules„ Communication settings Setting up Communication & Searching for Modules„ Broadcast search „ Designating model to search Ethernet Communication Module DVPEN01-SL „ Searching by IP address „ Opening DVPEN01-SL setup page by RS-232 „ Setting up DVPEN01-SL basics Basic Settings„ Setting up static IP of the PC Network SettingsEthernet Communication Module DVPEN01-SL Dhcp „ Setting up DVPEN01-SL Network„ Setting up DVPEN01-SL mail Setting up E-MailsData Exchange „ Setting up DVPEN01-SL data exchangeRTU „ The settingsStatic ARP Table „ Setting up IP filterIP Filter „ Setting up DVPEN01-SL password Setting up Password„ Setting up static ARP table „ DVPEN01-SL returning to default setting Returning to Default SettingApplication Examples Setting up IP and Communicating through WPLSoftEthernet Communication Module DVPEN01-SL Open Basic setup Switch to Network setup Connecting the PC with DVPEN01-SL through LAN DVPEN01 DVP-PLC Ethernet Communication Module DVPEN01-SL Ethernet Communication Module DVPEN01-SL Setting up Password and Clearing Password Ethernet Communication Module DVPEN01-SL After the password is cleared, you can modify the parameters IP Filter Protection Ethernet Communication Module DVPEN01-SL Setting up Static ARP Table Ethernet Communication Module DVPEN01-SL Application of E-Mail Explanations Application of Data ExchangeEthernet Communication Module DVPEN01-SL TRD Application of Data Exchange Ethernet Communication Module DVPEN01-SL Ethernet Communication Module DVPEN01-SL From Explanations Data exchange will be executed every one second Application of Modbus TCP Master RTU Mapping Ethernet Communication Module DVPEN01-SL Ethernet Communication Module DVPEN01-SL