Delta DVPEN01-SL operation manual Application of Data Exchange, Explanations

Page 47

Ethernet Communication Module DVPEN01-SL

4.Switch to “Select Recipients” page. Check all the boxes of “Recipient 1”. Click on “OK” to complete the setting.

5.After all the settings in DVPEN01-SL are completed, compile the ladder diagram in the MPU and download it to the MPU. See below for the program design:

X0
T0	K100	K3	K1	K1
X0
T0	K100	K4	K1	K1
Y0
T0	K100	K5	K1	K1
Y0
T0	K100	K6	K1	K1
END
Explanations:

•If the rising-edge of X0 is triggered, X0 will go from Off to On. Write “1” into CR#3 of DVPEN01-SL, and the first E-Mail will be sent out.

•If the falling-edge of X0 is triggered, X0 will go from On to Off. Write “1” into CR#4 of DVPEN01-SL, and the second E-Mail will be sent out.

•If the rising-edge of Y0 is triggered, Y0 will go from Off to On. Write “1” into CR#5 of DVPEN01-SL, and the third E-Mail will be sent out.

•If the falling-edge of Y0 is triggered, Y0 will go from On to Off. Write “1” into CR#6 of DVPEN01-SL, and the fourth E-Mail will be sent out.

6.8Application of Data Exchange (1)

Application

Network requirement

Writing the time in RTC in PLC_B into D0 ~ D6 of PLC_A

(1)Adopting static IP.

(2)IP of PLC_A: 192.168.0.4

(3)IP of PLC_B: 192.168.0.5”

(4)Update from PLC_B to PLC_A

DVP-PLC Operation Manual

45

Image 47

Contents DVPEN01-SL Page Table of Contents Application Examples Functions SpecificationsProduct Profiles DimensionRJ-45 PIN Definition LED IndicatorsInstallation Control Registers in DVPEN01-SL Control Register CREthernet Communication Module DVPEN01-SL „ E-mail Functions Explanations on CR„ Data Exchange Ethernet Communication Module DVPEN01-SL „ Sending Modbus TCP Instruction Ethernet Communication Module DVPEN01-SL „ RTU Mapping Numbering of Left-Side Modules„ Communication settings Setting up Communication & Searching for Modules„ Broadcast search „ Designating model to search Ethernet Communication Module DVPEN01-SL „ Searching by IP address „ Opening DVPEN01-SL setup page by RS-232 „ Setting up DVPEN01-SL basics Basic Settings„ Setting up static IP of the PC Network SettingsEthernet Communication Module DVPEN01-SL Dhcp „ Setting up DVPEN01-SL Network„ Setting up DVPEN01-SL mail Setting up E-MailsData Exchange „ Setting up DVPEN01-SL data exchangeRTU „ The settingsStatic ARP Table „ Setting up IP filterIP Filter „ Setting up DVPEN01-SL password Setting up Password„ Setting up static ARP table „ DVPEN01-SL returning to default setting Returning to Default SettingApplication Examples Setting up IP and Communicating through WPLSoftEthernet Communication Module DVPEN01-SL Open Basic setup Switch to Network setup Connecting the PC with DVPEN01-SL through LAN DVPEN01 DVP-PLC Ethernet Communication Module DVPEN01-SL Ethernet Communication Module DVPEN01-SL Setting up Password and Clearing Password Ethernet Communication Module DVPEN01-SL After the password is cleared, you can modify the parameters IP Filter Protection Ethernet Communication Module DVPEN01-SL Setting up Static ARP Table Ethernet Communication Module DVPEN01-SL Application of E-Mail Explanations Application of Data ExchangeEthernet Communication Module DVPEN01-SL TRD Application of Data Exchange Ethernet Communication Module DVPEN01-SL Ethernet Communication Module DVPEN01-SL From Explanations Data exchange will be executed every one second Application of Modbus TCP Master RTU Mapping Ethernet Communication Module DVPEN01-SL Ethernet Communication Module DVPEN01-SL