Compaq R6000 manual Front Panel LEDs, LED Meaning, Solid green means normal operation, Standby

Page 15

Introduction 1-5

Front Panel LEDs

The front panel has four LEDs to indicate the UPS operating mode.

Figure 1-3. The front panel

LED	LED Color	LED Meaning
	Green	Solid green means normal operation.
		Flashing green means Standby.
	Yellow	Solid yellow means the UPS is on Battery;
		flashing yellow means UPS is on Battery and
		Standby
	Yellow	Solid yellow means the UPS is on Bypass.
	Red	Solid red means current or impending problems.

Image 15

Contents Compaq R6000 Series UPS Operation and Reference Guide Page Contents Operation Configuration Appendix B Symbols in Text About This GuideText Conventions Viii Compaq R6000 Series UPS Operation and Reference Guide Symbols on EquipmentRack Stability Getting HelpCompaq Technical Support Compaq Website Compaq Authorized Reseller UPS Model Part Number Comments IntroductionCompaq R6000 UPS Series Models Compaq R6000 UPS Series ModelsR6000 front panel Front PanelRear Panel Communication Ports Compaq R6000 UPS FeaturesFlashing green means Standby Front Panel LEDsLED Meaning Solid green means normal operationControl Name Function Front Panel Controls and LCD DisplayCompaq Power Management Software Power Management SoftwareOption Part Number Hardware OptionsHardware Options UPS Option CardsOption Card Matrix CaseScalable Multi-Server UPS Card Compaq Multi-Server UPS CardScalable UPS Card Compaq Scalable UPS CardSNMP-EN Adapter Compaq SNMP-EN AdapterExtended Runtime Modules ERMs Power Distribution Units PDUsWarranty Remote Emergency Power Off Repo Port$25,000 Computer Load Protection Guarantee Pre-Failure Battery Warranty Important Safety Instructions About This Device InstallationInstallation Considerations WeightPosition Outline of Installation Procedure Check Battery Recharge Label Unpacking the UPSPreparing the Rack Placing UPS in rack Assembling the Compaq R6000 UPSPlacing chassis in rack Wiring the Compaq R6000 UPS 8Compaq R6000 Series UPS Operation and Reference Guide Connecting the Compaq R6000 UPS to AC Branch Circuit Risk of Fire Notice Electrical Safety RequirementsHigh Leakage Current Recommendation ProcedureRemoving terminal input block cover Input WiringSliding battery packs into chassis Install and connect the battery packsConnect cables 11. Connecting battery packs to the Compaq R6000 UPS 12. Attaching the top front bezel Attaching Front Top BezelInstalling Extended Runtime Modules ERMs Connecting Communication Ports to Other Devices Connecting Communications PortsConnecting Loads Installing and Connecting Communication OptionsLoad Segments Description Attaching the Load Segments Ordering Extra Power CordsConfiguring Load Segments Load Effect on Backup Time16. Placing the battery circuit breaker in the on position Completing the Assembly R6000 UPS in the RackShutting Down the System Powering up the R6000 UPSTurning on the Main Circuit Breaker Pressing the on buttonCharging Batteries Installation is Now CompleteOperation Front Panel Controls Front Panel LCD Front Panel IndicatorsFront Panel LEDs Ref # Description Modes of Operation Standby ModeBattery Mode Initiating a Self-test Audible AlarmSilencing an audible alarm Silencing an Audible AlarmChanging Configuration Parameters ConfigurationMatching the Utility Voltage Voltage Ranges VACRange LCD display, showing the three buttons that control it Configuring the Compaq R6000 UPS Using the LCD Display MenuSub-Menu Choices Initial Power-Up DisplayLCD Display Menu Structure Top Level Main MenuUPS Status + Load Segment status StatusLoad Power On UPS Status + Active Alarm CountOn Battery Load Power OffOutput Volts MetersOverload Input VoltsOutput Frequency Active AlarmsOutput Power Battery VoltsOutput Overload Input AC Over VoltageInput AC Under Voltage Input Over or Under FrequencyUPS on Battery Inverter FaultBattery Low Battery Totally DischargedBattery Data Battery Test FailedSite Wiring Fault Firmware Version Display Test Load ControlSet Hardware HW Configuration System SetupSet Language Battery SetupSet Password Set Alarm HornBaud Rate Communications SetupSet Sync Range ±Hertz Serial PortStop Bits Data BitsParity Set Site Fault Set Sleep ModeSet Voltage Battery Maintenance Precautions Obtaining New Batteries When to Replace BatteriesHow to Replace Batteries Removing the Battery PacksBefore Replacing Batteries Place the battery circuit breaker in the OFF position Disconnecting the battery cables Slide out the Compaq R6000 UPS battery packs Installing New Batteries Test/Reset Alarm button Disposing of Used Batteries Care and Storage of BatteriesExtended Runtime Module ERM Batteries Troubleshooting Responding to Audible Alarms Audible Alarm GroupCauses Action Shutdown Imminent Seconds Causes Action Shutdown withinLoads in Jeopardy Audible Alarm Low, refer to Chapter Causes Action6Compaq R6000 UPS Series Operation and Reference Guide Battery breaker is in the on Responding to Audible Alarms Audible Alarm GroupTrouble Indicators Compaq R6000 UPS Trouble IndicatorsLED Alarm Configurations Repairing the UPS Federal Communications Commission Notice Regulatory Compliance NoticesClass B Equipment Class a EquipmentEuropean Union Notice Canadian Notice Avis CanadienJapanese Notice Taiwanese NoticeClass A/B Equipment Battery Replacement Notice Electrostatic Discharge Grounding Methods Specifications Table C-2 Input Specifications Physical SpecificationsInput Specifications Table C-1 Physical CharacteristicsOutput Specifications IV. Additional Features II. Output VoltageRegulation Table C-4 Battery SpecificationsBattery Runtime Battery SpecificationsTable C-6 Environmental Specifications Environmental SpecificationsIndex Battery cable connectors Button controls Index Compaq 6000 Series UPS Operation and Reference Guide See Compaq 6000 Series UPS Operation and Reference Guide Replacement battery kit part Compaq 6000 Series UPS Operation and Reference Guide Options tabulated Compaq 6000 Series UPS Operation and Reference Guide