Compaq manual Completing the Assembly R6000 UPS in the Rack

Page 45

2-20Compaq R6000 Series UPS Operation and Reference Guide

Completing the Assembly of the

R6000 UPS in the Rack

Figure 2-16. Placing the battery circuit breaker in the ON position

NOTE: If optional Extended Runtime Modules are attached, place the ERM battery circuit breakers in the ON position after the UPS circuit breaker is placed in the ON position.

Attach the front bottom bezel using the two captive screws.

Figure 2-17. Attaching the front bottom bezel

Image 45

Contents Compaq R6000 Series UPS Operation and Reference Guide Page Contents Operation Configuration Appendix B Symbols in Text About This GuideText Conventions Viii Compaq R6000 Series UPS Operation and Reference Guide Symbols on EquipmentRack Stability Getting HelpCompaq Technical Support Compaq Website Compaq Authorized Reseller Compaq R6000 UPS Series Models IntroductionCompaq R6000 UPS Series Models UPS Model Part Number CommentsR6000 front panel Front PanelRear Panel Communication Ports Compaq R6000 UPS FeaturesLED Meaning Front Panel LEDsSolid green means normal operation Flashing green means StandbyControl Name Function Front Panel Controls and LCD DisplayCompaq Power Management Software Power Management SoftwareHardware Options Hardware OptionsUPS Option Cards Option Part NumberOption Card Matrix CaseScalable Multi-Server UPS Card Compaq Multi-Server UPS CardScalable UPS Card Compaq Scalable UPS CardSNMP-EN Adapter Compaq SNMP-EN AdapterExtended Runtime Modules ERMs Power Distribution Units PDUsWarranty Remote Emergency Power Off Repo Port$25,000 Computer Load Protection Guarantee Pre-Failure Battery Warranty Important Safety Instructions About This Device InstallationInstallation Considerations WeightPosition Outline of Installation Procedure Check Battery Recharge Label Unpacking the UPSPreparing the Rack Placing UPS in rack Assembling the Compaq R6000 UPSPlacing chassis in rack Wiring the Compaq R6000 UPS 8Compaq R6000 Series UPS Operation and Reference Guide Connecting the Compaq R6000 UPS to AC Branch Circuit Risk of Fire Notice Electrical Safety RequirementsHigh Leakage Current Recommendation ProcedureRemoving terminal input block cover Input WiringSliding battery packs into chassis Install and connect the battery packsConnect cables 11. Connecting battery packs to the Compaq R6000 UPS 12. Attaching the top front bezel Attaching Front Top BezelInstalling Extended Runtime Modules ERMs Connecting Communication Ports to Other Devices Connecting Communications PortsConnecting Loads Installing and Connecting Communication OptionsLoad Segments Description Configuring Load Segments Ordering Extra Power CordsLoad Effect on Backup Time Attaching the Load Segments16. Placing the battery circuit breaker in the on position Completing the Assembly R6000 UPS in the RackTurning on the Main Circuit Breaker Powering up the R6000 UPSPressing the on button Shutting Down the SystemCharging Batteries Installation is Now CompleteOperation Front Panel Controls Front Panel LCD Front Panel IndicatorsFront Panel LEDs Ref # Description Modes of Operation Standby ModeBattery Mode Initiating a Self-test Audible AlarmSilencing an audible alarm Silencing an Audible AlarmChanging Configuration Parameters ConfigurationMatching the Utility Voltage Voltage Ranges VACRange LCD display, showing the three buttons that control it Configuring the Compaq R6000 UPS Using the LCD Display MenuLCD Display Menu Structure Initial Power-Up DisplayTop Level Main Menu Sub-Menu ChoicesUPS Status + Load Segment status StatusOn Battery UPS Status + Active Alarm CountLoad Power Off Load Power OnOverload MetersInput Volts Output VoltsOutput Power Active AlarmsBattery Volts Output FrequencyInput AC Under Voltage Input AC Over VoltageInput Over or Under Frequency Output OverloadBattery Low Inverter FaultBattery Totally Discharged UPS on BatteryBattery Data Battery Test FailedSite Wiring Fault Firmware Version Display Test Load ControlSet Hardware HW Configuration System SetupSet Language Battery SetupSet Password Set Alarm HornSet Sync Range ±Hertz Communications SetupSerial Port Baud RateStop Bits Data BitsParity Set Site Fault Set Sleep ModeSet Voltage Battery Maintenance Precautions Obtaining New Batteries When to Replace BatteriesHow to Replace Batteries Removing the Battery PacksBefore Replacing Batteries Place the battery circuit breaker in the OFF position Disconnecting the battery cables Slide out the Compaq R6000 UPS battery packs Installing New Batteries Test/Reset Alarm button Disposing of Used Batteries Care and Storage of BatteriesExtended Runtime Module ERM Batteries Troubleshooting Responding to Audible Alarms Audible Alarm GroupCauses Action Shutdown Imminent Seconds Causes Action Shutdown withinLoads in Jeopardy Audible Alarm Low, refer to Chapter Causes Action6Compaq R6000 UPS Series Operation and Reference Guide Battery breaker is in the on Responding to Audible Alarms Audible Alarm GroupTrouble Indicators Compaq R6000 UPS Trouble IndicatorsLED Alarm Configurations Repairing the UPS Federal Communications Commission Notice Regulatory Compliance NoticesClass B Equipment Class a EquipmentEuropean Union Notice Canadian Notice Avis CanadienJapanese Notice Taiwanese NoticeClass A/B Equipment Battery Replacement Notice Electrostatic Discharge Grounding Methods Specifications Input Specifications Physical SpecificationsTable C-1 Physical Characteristics Table C-2 Input SpecificationsOutput Specifications IV. Additional Features II. Output VoltageRegulation Battery Runtime Battery SpecificationsBattery Specifications Table C-4Table C-6 Environmental Specifications Environmental SpecificationsIndex Battery cable connectors Button controls Index Compaq 6000 Series UPS Operation and Reference Guide See Compaq 6000 Series UPS Operation and Reference Guide Replacement battery kit part Compaq 6000 Series UPS Operation and Reference Guide Options tabulated Compaq 6000 Series UPS Operation and Reference Guide