Compaq manual Assembling the Compaq R6000 UPS, Placing UPS in rack

Page 30

Installation 2-5

Assembling the Compaq R6000 UPS

Placing UPS in rack.

68-136 kg

150-300 lb

WARNING: This product is heavier than it appears. To reduce the risk of personal injury or damage to the equipment:

■Observe local occupational health and safety requirements and guidelines for manual material handling.

■Obtain adequate assistance to lift and stabilize the product during installation or removal. The product will be unstable when not fastened to the rails.

■Remove all pluggable power supplies and modules to reduce the overall weight of the product.

68-136 kg

150-300 lb

WARNING: To reduce the risk of personal injury or damage to the equipment, take the following precautions when installing the equipment:

■The Compaq R6000 UPS and the Extended Runtime Modules (ERMs) MUST be installed at the bottom of the rack. If placed in rack with existing equipment, the rack must be re-configured to allow installation of UPS at the bottom of the rack.

■The Compaq R6000 UPS must be mounted on the fixed rails included in the UPS package. Refer to the appropriate installation card and rack template, also shipped with your Compaq R6000 UPS kit for instructions on rack-mounting the Compaq R6000 UPS.

NOTE: If installing an Extended Runtime Module (ERM) with the Compaq R6000 UPS, the ERM must be installed at the bottom of the rack, with the UPS immediately above. If the UPS is installed without an ERM, the UPS must be installed at the bottom of the rack.

After the rails are secured in the rack:

1.With one person on each side of the box, remove the UPS chassis from the package using the lift-out tray.

2.Gently lower the chassis to the floor in front of the rack.

3.Cut the band that holds the chassis, freeing it from the lift-out tray.

4.With one person on each side, lift the chassis to rail level and slide into place.

5.Attach the chassis to the rack using screws and cage nuts supplied with the rack.

Image 30

Contents Compaq R6000 Series UPS Operation and Reference Guide Page Contents Operation Configuration Appendix B Symbols in Text About This GuideText Conventions Symbols on Equipment Viii Compaq R6000 Series UPS Operation and Reference GuideRack Stability Getting HelpCompaq Technical Support Compaq Website Compaq Authorized Reseller Compaq R6000 UPS Series Models IntroductionCompaq R6000 UPS Series Models UPS Model Part Number CommentsFront Panel R6000 front panelRear Panel Compaq R6000 UPS Features Communication PortsSolid green means normal operation Front Panel LEDsLED Meaning Flashing green means StandbyFront Panel Controls and LCD Display Control Name FunctionPower Management Software Compaq Power Management SoftwareUPS Option Cards Hardware OptionsHardware Options Option Part NumberOption Card Matrix CaseScalable Compaq Multi-Server UPS Card Multi-Server UPS CardCompaq Scalable UPS Card Scalable UPS CardCompaq SNMP-EN Adapter SNMP-EN AdapterPower Distribution Units PDUs Extended Runtime Modules ERMsWarranty Remote Emergency Power Off Repo Port$25,000 Computer Load Protection Guarantee Pre-Failure Battery Warranty Installation Important Safety Instructions About This DeviceInstallation Considerations WeightPosition Outline of Installation Procedure Check Battery Recharge Label Unpacking the UPSPreparing the Rack Assembling the Compaq R6000 UPS Placing UPS in rackPlacing chassis in rack Wiring the Compaq R6000 UPS 8Compaq R6000 Series UPS Operation and Reference Guide Connecting the Compaq R6000 UPS to AC Branch Circuit Risk of Fire Notice Electrical Safety RequirementsHigh Leakage Current Procedure RecommendationInput Wiring Removing terminal input block coverInstall and connect the battery packs Sliding battery packs into chassisConnect cables 11. Connecting battery packs to the Compaq R6000 UPS Attaching Front Top Bezel 12. Attaching the top front bezelInstalling Extended Runtime Modules ERMs Connecting Communications Ports Connecting Communication Ports to Other DevicesConnecting Loads Installing and Connecting Communication OptionsLoad Segments Description Load Effect on Backup Time Ordering Extra Power CordsConfiguring Load Segments Attaching the Load SegmentsCompleting the Assembly R6000 UPS in the Rack 16. Placing the battery circuit breaker in the on positionPressing the on button Powering up the R6000 UPSTurning on the Main Circuit Breaker Shutting Down the SystemInstallation is Now Complete Charging BatteriesOperation Front Panel Controls Front Panel Indicators Front Panel LCDFront Panel LEDs Ref # Description Standby Mode Modes of OperationBattery Mode Audible Alarm Initiating a Self-testSilencing an Audible Alarm Silencing an audible alarmConfiguration Changing Configuration ParametersMatching the Utility Voltage Voltage Ranges VACRange Configuring the Compaq R6000 UPS Using the LCD Display Menu LCD display, showing the three buttons that control itTop Level Main Menu Initial Power-Up DisplayLCD Display Menu Structure Sub-Menu ChoicesStatus UPS Status + Load Segment statusLoad Power Off UPS Status + Active Alarm CountOn Battery Load Power OnInput Volts MetersOverload Output VoltsBattery Volts Active AlarmsOutput Power Output FrequencyInput Over or Under Frequency Input AC Over VoltageInput AC Under Voltage Output OverloadBattery Totally Discharged Inverter FaultBattery Low UPS on BatteryBattery Data Battery Test FailedSite Wiring Fault Firmware Version Load Control Display TestSystem Setup Set Hardware HW ConfigurationBattery Setup Set LanguageSet Alarm Horn Set PasswordSerial Port Communications SetupSet Sync Range ±Hertz Baud RateData Bits Stop BitsParity Set Site Fault Set Sleep ModeSet Voltage Battery Maintenance Precautions When to Replace Batteries Obtaining New BatteriesHow to Replace Batteries Removing the Battery PacksBefore Replacing Batteries Place the battery circuit breaker in the OFF position Disconnecting the battery cables Slide out the Compaq R6000 UPS battery packs Installing New Batteries Test/Reset Alarm button Disposing of Used Batteries Care and Storage of BatteriesExtended Runtime Module ERM Batteries Troubleshooting Responding to Audible Alarms Audible Alarm GroupCauses Action Shutdown Imminent Causes Action Shutdown within SecondsLoads in Jeopardy Audible Alarm Causes Action Low, refer to Chapter6Compaq R6000 UPS Series Operation and Reference Guide Responding to Audible Alarms Audible Alarm Group Battery breaker is in the onCompaq R6000 UPS Trouble Indicators Trouble IndicatorsLED Alarm Configurations Repairing the UPS Regulatory Compliance Notices Federal Communications Commission NoticeClass a Equipment Class B EquipmentCanadian Notice Avis Canadien European Union NoticeJapanese Notice Taiwanese NoticeClass A/B Equipment Battery Replacement Notice Electrostatic Discharge Grounding Methods Specifications Table C-1 Physical Characteristics Physical SpecificationsInput Specifications Table C-2 Input SpecificationsOutput Specifications IV. Additional Features II. Output VoltageRegulation Battery Specifications Battery SpecificationsBattery Runtime Table C-4Environmental Specifications Table C-6 Environmental SpecificationsIndex Battery cable connectors Button controls Index Compaq 6000 Series UPS Operation and Reference Guide See Compaq 6000 Series UPS Operation and Reference Guide Replacement battery kit part Compaq 6000 Series UPS Operation and Reference Guide Options tabulated Compaq 6000 Series UPS Operation and Reference Guide