BOXLIGHT MP-86i 1Remove the battery cover, 2Loading the batteries, 3Close the battery cover

Page 11
PLACE OF MANUFACTURER:A
MADE IN JAPAN

Names and functions of each part (continued)

Caution • Auto adjust can take up to 30 seconds.

Auto adjust may not operate correctly in some cases, depending on the computer connected and the signal.

Be sure to expand images to full screen size when displaying low resolution images.

After auto adjust, the image may be slightly dark in some cases due to automatic adjustment of the signal level.

Auto adjust can not execute when the initial display is “NO INPUT IS DETECTED” or “SYNC IS OUT OF RANGE” during FREEZE or MAGNIFY.

Auto Adjust is executed when the following operations are performed.

1.When the type of input source signal is changed.

2.When the Auto Adjust (AUTO) button is pressed.

The message AUTO IN PROGRESS will be displayed on the screen during automatic adjustment.

The screen may be disrupted during automatic adjustment but this is not a malfunction.

RGB1 or RGB2 only can be used as the input signal.

Auto Adjust can also be executed using the operation buttons of the main unit. Hold down the RESET button and press the input switch (INPUT) button.

Loading the batteries Loading AA batteries into the remote control.

1Remove the battery cover.

Push the knob while lifting up the battery cover.

Caution Battery usage cautions

Use only the specified batteries with this projector. Also, do not mix new and old batteries. This could cause battery cracking or leakage, which could result in fire or personal injury.

When loading the batteries, make sure the plus and minus poles are correctly oriented as indicated in the remote control. Incorrect orientation could cause battery cracking or leakage, which could result in personal injury or pollution of the surrounding environment.

2Loading the batteries.

Make sure the plus and minus poles are correctly oriented.

3Close the battery cover.

Caution Remote control usage cautions

Do not drop the remote control or apply impact.

Do not wet the remote control or place it on any wet object. Such actions could result in malfunction.

When not to be used for an extended period, remove the batteries from the remote control.

Replace the batteries when remote control operation becomes difficult.

Do not place the remote control close to the cooling fan of the projector.

Do not disassemble the remote control in case of malfunction. please contact BOXLIGHT Corporation.

Warning

The laser pointer of the remote control is used as a pointer.

 

Never look directly into the laser beam outlet or point the laser beam at

 

other people.

 

The laser beam can cause vision problems.

 

 

C A U T I O N

LASER RADIATION-

DO NOT STARE INTO BEAM

WAVE LENGTH: 650nm

MAX . OUTPUT: 1mW

CLASS 2 LASER PRODUCT

RADIAZIONI LASER

NON GUARDARE NEL RAGGIO LUCE

APPARECCHIO LASER DI CLASSE 2

RAYONNEMENT LASER MANUFACTURED

NE PAS REGARDER DANS

LE FAISCEAU APPAREIL

A LASER DE CLASSE 2

LASER-STRAHLUNG

NICHT IN DEN STRAHL

BLICKEN LASER KLASSE2

IEC60825-1:1993+A1:1997

AVOID EXPOSURE-

LASER RADIATION IS

EMITTED FROM THIS

APERTURE

11

Image 11
Contents Outline FeaturesContents For the Customers in U.K Video inputs Video signal cablesPower cord Before UseUse only the indicated power supply If a problem should occurDo not install on an unstable surface Do not look through the lens when the lamp is onDo not allow the laser beam to enter the eyes Handle the power cord with careDo not position the power Avoid installation in humid or dusty locations Care and maintenanceBattery usage Clean the projector interior once every two yearsCabinet care Sound volumeAvoid excessively hot locations Lens careNames and functions of each part Checking the package ContentsNames and functions of each part Names and functions of each part Remote control transmitter2Loading the batteries 1Remove the battery cover3Close the battery cover Top view Side view InstallationTypical LCD Projector and Screen Installation Using the adjustersTo project Turn on the main power switch of the projector I onTurn on the power to the connected equipment Basic operationsPress the STANDBY/ON button for approximately 1 second Turning off the powerTurn off the main power switch of the projector OFF Plug & PlayPress the Freeze button Cancelling the Freeze functionFreeze function Returning to normal display Magnify functionChanging the magnification ratio Moving the display areaPress the Menu Adjustments and functionsReturning to the initial settings Using the Setup Menu SET UPInput Image OPT Signal input jacks Connection to the video signal terminalsConnection to the RGB signal terminal Input signalsExample of computer signal Connection to the RGB signal terminalInitial set signals Connection to the RGB signal terminalConnecting the USB Mouse functions Connection to the control signal terminalControl signal jack Connection to the control signal terminalRS232C communication System Video Command data chartRequesting projector status Remove the front air filter Example of system setupCleaning the Air filter Pull out the power cordMessage table Clean the air filter with a vacuum cleanerInstall the air filter LampIndicators TroubleshootingDimensional Diagram Limited Warranty About the warranty and after-serviceQR41981