BOXLIGHT MP-86i user manual Avoid excessively hot locations, Sound volume, Lens care, Cabinet care

Page 7
Disconnect the plug from the power outlet.

Caution

When the projector is not to be used for an extended period.

Moving the projector.

When moving the projector, be sure

For safety purposes when the projector is not to be used for an extended period because of travel, etc., always disconnect the power plug from the power outlet. Also close the lens cover to prevent the lens surface being scratched.

Disconnect the plug from the power outlet.

to replace lens cap, disconnect the power plug from the power outlet and disconnect all external connections. Failure to do this could damage the power cord and cause fire or electrical shock.

Avoid any impact or shock to the projector

because this could result in malfunction.

When moving this projector outdoors, protect it from wetness due to rain, etc. If

the projector should become wet, dry it thoroughly before further use. Continued use while wet could result in fire or electrical shock.

[General Cautions]

Avoid excessively hot locations.

Do not place this projector in direct sunlight or near a hot object such as a stove, etc., because the heat could have adverse influence on the cabinet and other parts.

Sound volume.

Set the volume at a suitable level to avoid bothering other people. It is also better to keep the volume level low and close the windows at night to protect the neighborhood environment.

Lens care

Use commercially available lens tissue to clean the lens (used to clean cameras, eyeglasses, etc.). Be careful not to scratch the lens with hard objects.

Cabinet care.

The cabinet is made of plastic and discoloration or paint peeling can occur if wiped with a solvent

such as benzine, thinner, etc.

Before using chemical wipes, be sure to read and observe the instructions.

Do not spray volatile substances on the cabinet. Also, do not allow long-term close

contact with rubber or vinyl products because this could result in discoloration, peeling paint, etc.

Use a soft cloth to clean the cabinet and operation panel. When excessively soiled,

dilute a neutral detergent in water, wet and wring out the cloth and afterward wipe with a dry cloth. Do not apply undiluted detergent directly to the projector.

Extended usage.

When using this projector for an extended period, stop periodically to rest the eyes to prevent eye fatigue.

7

Image 7
Contents Contents FeaturesOutline For the Customers in U.K Video inputs Video signal cablesPower cord Before UseUse only the indicated power supply If a problem should occurDo not install on an unstable surface Do not look through the lens when the lamp is onDo not position the power Handle the power cord with careDo not allow the laser beam to enter the eyes Avoid installation in humid or dusty locations Care and maintenanceBattery usage Clean the projector interior once every two yearsCabinet care Sound volumeAvoid excessively hot locations Lens careNames and functions of each part Checking the package ContentsNames and functions of each part Names and functions of each part Remote control transmitter3Close the battery cover 1Remove the battery cover2Loading the batteries Top view Side view InstallationTypical LCD Projector and Screen Installation Using the adjustersTo project Turn on the main power switch of the projector I onTurn on the power to the connected equipment Basic operationsPress the STANDBY/ON button for approximately 1 second Turning off the powerTurn off the main power switch of the projector OFF Plug & PlayFreeze function Cancelling the Freeze functionPress the Freeze button Returning to normal display Magnify functionChanging the magnification ratio Moving the display areaReturning to the initial settings Adjustments and functionsPress the Menu Using the Setup Menu SET UPInput Image OPT Signal input jacks Connection to the video signal terminalsConnection to the RGB signal terminal Input signalsExample of computer signal Connection to the RGB signal terminalInitial set signals Connection to the RGB signal terminalConnecting the USB Mouse functions Connection to the control signal terminalControl signal jack Connection to the control signal terminalRS232C communication System Video Command data chartRequesting projector status Remove the front air filter Example of system setupCleaning the Air filter Pull out the power cordMessage table Clean the air filter with a vacuum cleanerInstall the air filter LampIndicators TroubleshootingDimensional Diagram Limited Warranty About the warranty and after-serviceQR41981