BOXLIGHT MP-86i user manual Connection to the control signal terminal, Mouse functions

Page 26

Connection to the control signal terminal

1.Mouse functions

(1)Turn off the main power switches of the projector and computer and connect the two units with the cable provided or an optional suitable commercially available cable. Disconnect the USB cable from the projector.

(2)Turn on the main switch of the projector (the POWER indicator lamp will light green).

(3)Press the INPUT button of the projector or the RGB button of the remote control and select the input where the computer is connected.

(4)Turn on the computer power supply.

(5)Start the mouse function.

If the mouse has not been started, reboot the computer (soft reboot or reboot buttons).

(6)Refer to page 10 concerning remote control operation.

(7)Varying the force with which the DISK PAD button is pressed varies the speed of mouse operation.

PS/2 Mouse

Projector

Computer

Mouse jack Mini

 

 

1

1

DATA

DIN 6-pin

 

 

 

 

 

CLK 2

2

 

 

 

control jack

DATA 3

3

GND

6

5

D-sub 15-pin shrink jack

 

4

4

+5V

 

4

3

 

 

5

5

CLK

 

SEL0

6

6

 

2

1

 

RTS

7

 

 

 

 

 

 

 

 

 

8

 

 

 

 

+5V

9

GND

10

11

12

13

14Mouse cable (PS/2)

Use the mouse cable provided.

Cables for ADB mouse (Apple), bus mouse (NEC) and serial mouse are available as options.

Caution • Before making connections, read the instruction manual of the equipment to be connected.

• Turn off the projector and computer power supplies before connecting.

Connecting the mouse cable with the computer power on can result in a malfunction. Use the mouse cable provided to make the connection.

•In the case of notebook type computers with a built-in pointing device such as a track ball, in some cases the built-in pointing device will have priority even if a mouse is connected and the mouse may not be selected.

In such case, disable the built-in pointing device and change the BIOS setting (system setup) so that an external mouse can be selected.

After changing the BIOS setting, perform the operations described in (1) - (3) above. Refer to the computer hardware manual concerning the BIOS setting.

Also, some computers may not have a utility program to operate a mouse. Refer to the computer hardware manual.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Outline FeaturesContents For the Customers in U.K Before Use Video signal cablesPower cord Video inputsDo not look through the lens when the lamp is on If a problem should occurDo not install on an unstable surface Use only the indicated power supplyDo not allow the laser beam to enter the eyes Handle the power cord with careDo not position the power Clean the projector interior once every two years Care and maintenanceBattery usage Avoid installation in humid or dusty locationsLens care Sound volumeAvoid excessively hot locations Cabinet careChecking the package Contents Names and functions of each partNames and functions of each part Remote control transmitter Names and functions of each part2Loading the batteries 1Remove the battery cover3Close the battery cover Using the adjusters InstallationTypical LCD Projector and Screen Installation Top view Side viewBasic operations Turn on the main power switch of the projector I onTurn on the power to the connected equipment To projectPlug & Play Turning off the powerTurn off the main power switch of the projector OFF Press the STANDBY/ON button for approximately 1 secondPress the Freeze button Cancelling the Freeze functionFreeze function Moving the display area Magnify functionChanging the magnification ratio Returning to normal displayPress the Menu Adjustments and functionsReturning to the initial settings SET UP Using the Setup MenuInput Image OPT Input signals Connection to the video signal terminalsConnection to the RGB signal terminal Signal input jacksConnection to the RGB signal terminal Example of computer signalConnection to the RGB signal terminal Initial set signalsConnecting the USB Connection to the control signal terminal Mouse functionsConnection to the control signal terminal Control signal jackRS232C communication Command data chart System VideoRequesting projector status Pull out the power cord Example of system setupCleaning the Air filter Remove the front air filterLamp Clean the air filter with a vacuum cleanerInstall the air filter Message tableTroubleshooting IndicatorsDimensional Diagram About the warranty and after-service Limited WarrantyQR41981
Top Page Image Contents