BOXLIGHT MP-86i Do not sit or place heavy objects on this projector, Care and maintenance

Page 6

Caution

Do not sit or place heavy objects on this projector.

Do not sit on this projector.

This could result in overturning, leading to damage or personal injury. Use special caution in households where children are present.

Do not place heavy objects on this projector.

Placing heavy objects on this projector could result in loss of balance or falling and cause personal injury.

Do not block the ventilation openings.

Do not block the ventilation openings of this projector. Blocking ventilation could lead to internal overheating which could result in fire. Do not place this projector on its

side during use or push it into a small, poorly ventilated location. Do not place this projector on a carpet or bedding or cover it with a table cloth,

etc. Also, when installing this projector, make sure the ventilation openings are at least 12"(30cm) from the wall.

Care and maintenance.

For safety purposes, disconnect the power plug from the power outlet

before starting the care and maintenance of this projector.

Disconnect the plug from the power outlet.

Battery usage.

Use only the specified batteries with this projector. Do not mix old

and new batteries because this could result in fire or personal injury due to battery cracking or leakage.

Make sure the plus and minus terminals are correctly aligned

when loading the batteries.

Incorrect loading could result in personal injury or contamination of

the surroundings due to battery cracking or leakage.

Clean the projector interior once every two years.

Request your dealer to clean the interior of the projector approximately every two years. Accumulations of dust inside the projector can result in fire or

malfunction if not cleaned for an extended period. This cleaning is more effective if performed before very humid periods. Ask your dealer for details about internal cleaning.

Avoid installation in humid or dusty locations.

Do not install this projector in a humid or dusty location. This could

result in fire or electrical shock.

Avoid installation near the

kitchen, a humidifier or other locations where there is oily smoke or humidity.

This could result in fire or electrical shock.

Use the caster brakes.

When installing this projector on a stand with casters, use the caster brakes to prevent the stand moving or overturning and causing personal injury.

Do not handle the power cord roughly.

Keep the power cord away from heaters because the heat could melt the

power cord and cause fire or electrical shock.

Do not touch the power plug

with wet hands because this

could result in electrical shock.

When disconnecting the

power plug, do not pull on the power cord. This could damage the power cord and cause fire or electrical shock. Always grip the plug when disconnecting, not the cord.

6

Image 6
Contents Features ContentsOutline For the Customers in U.K Before Use Video signal cablesPower cord Video inputsDo not look through the lens when the lamp is on If a problem should occurDo not install on an unstable surface Use only the indicated power supplyHandle the power cord with care Do not position the powerDo not allow the laser beam to enter the eyes Clean the projector interior once every two years Care and maintenanceBattery usage Avoid installation in humid or dusty locationsLens care Sound volumeAvoid excessively hot locations Cabinet careChecking the package Contents Names and functions of each partNames and functions of each part Remote control transmitter Names and functions of each part1Remove the battery cover 3Close the battery cover2Loading the batteries Using the adjusters InstallationTypical LCD Projector and Screen Installation Top view Side viewBasic operations Turn on the main power switch of the projector I onTurn on the power to the connected equipment To projectPlug & Play Turning off the powerTurn off the main power switch of the projector OFF Press the STANDBY/ON button for approximately 1 secondCancelling the Freeze function Freeze functionPress the Freeze button Moving the display area Magnify functionChanging the magnification ratio Returning to normal displayAdjustments and functions Returning to the initial settingsPress the Menu SET UP Using the Setup MenuInput Image OPT Input signals Connection to the video signal terminalsConnection to the RGB signal terminal Signal input jacksConnection to the RGB signal terminal Example of computer signalConnection to the RGB signal terminal Initial set signalsConnecting the USB Connection to the control signal terminal Mouse functionsConnection to the control signal terminal Control signal jackRS232C communication Command data chart System VideoRequesting projector status Pull out the power cord Example of system setupCleaning the Air filter Remove the front air filterLamp Clean the air filter with a vacuum cleanerInstall the air filter Message tableTroubleshooting IndicatorsDimensional Diagram About the warranty and after-service Limited WarrantyQR41981