BOXLIGHT CP-33t manual Basic Operations, Turning On / Off The Projector, Turning On The Projector

Page 20

BASIC OPERATIONS

BASIC OPERATIONS

TURNING ON / OFF THE PROJECTOR

TURNING ON THE PROJECTOR

1	Complete the peripheral connections (with Computer, VCR,
1	etc.) before turning on the projector. (Refer to "CONNECTING
	TO THE PROJECTOR" on Pages 10~13 for connecting that
	equipment.
2	Connect the projector's AC power cord into a wall outlet. The
2	LAMP indicator lights RED, and the READY indicator lights
	GREEN.
3	Press the power ON-OFF button on the Remote Control Unit or
3	on the Top Control to ON. The LAMP POWER indicator dims,

and the Cooling Fans start to operate. The Preparation Display appears on the screen and the count-down starts. The signal from the source appears after 30 seconds.

30

The Preparation Display disappears after 30 seconds.

	TURNING OFF THE PROJECTOR
1	Press the power ON-OFF button on the Remote Control Unit or
1	on the Top Control, and the message "Power off?" appears on
	the screen.
2	Press again the power ON-OFF button to turn off the projector.
2	The LAMP indicator lights bright and the READY indicator turns
	off. The Cooling Fans operate for 90 seconds after the
	projector is turned off. (During this "Cooling Down" period, this
	appliance cannot be turned on.)
3	When the cooling the projector has finished, the READY
3	indicator turns to green again and you can turn the projector

on. After cooling down completely, disconnect the AC power cord.

Power off?

The message disappears after 4 seconds.

TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU TURN IT ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF.

When the TEMPERATURE WARNING indicator flashes red, the projector is automatically turned off. Wait at least 5 minutes before turning the projector on again.

If the TEMPERATURE WARNING indicator continues to flash, follow procedures below:

1.Disconnect the AC power cord from the AC outlet.

2.Check the air filters for dust accumulation.

3.Clean the Air Filter. (See "AIR FILTER CARE AND CLEANING" section on page 42.)

4.Press the power ON-OFF button to ON.

If the TEMPERATURE WARNING indicator still continues to flash, call Boxlight at 1-800-762-5757 or 360- 779-7901.

NOTE: The Cooling Fan may work for cooling while the projector is turned off. When the Cooling Fan is working, TEMPERATURE WARNING INDICATOR flashes red.

20

Image 20

Contents USER’S GUIDE BOXLIGHTBOXLIGHT CP-33t SAFETY PRECAUTIONS TO THE OWNERINFORMATION TO THE USER RISK OF ELECTRIC SHOCK DO NOT OPENIMPORTANT SAFETY INSTRUCTIONS TABLE OF CONTENTS FEATURES AND DESIGNSETTING 5 COMPUTER MODEFEATURES AND DESIGN Image ResolutionOther Features AccessoriesPOWER CORD CONNECTOR ADJUSTABLE FEET AND FEET LOCK LATCHESPREPARATION NAME OF EACH PART OF THE PROJECTORSETTING-UP THE PROJECTOR ADJUSTABLE FEETPOSITIONING THE PROJECTOR ROOM LIGHTPREPARATION CONNECTING THE AC POWER CORD VENTILATIONCAUTION WHEN CARRYING OR TRANSPORTING THE PROJECTOR PREPARATION MOVING THE PROJECTORCONNECTING THE PROJECTOR CONTROL PORT CONNECTORTERMINALS OF THE PROJECTOR S-VIDEO INPUT JACK VIDEO INPUT JACKTerminals of the Projector CONNECTING TO THE VIDEO EQUIPMENTCONNECTING THE PROJECTOR CONNECTING TO THE COMPUTER To connect to the computer, refer to the figure belowTerminal Terminal Terminaling on the RESOLUTION MAC ADAPTER Not suppliedin the table below depend MODE that you want toOPERATION OF THE REMOTE CONTROL BEFORE OPERATIONLeft Side LASER POINTER FUNCTIONREMOTE CONTROL BATTERIES INSTALLATION Operating Range16.4’ 5 m 16.4’ 5 m VOLUME BUTTONTOP CONTROLS AND INDICATORS POWER ON-OFF BUTTONLAMP INDICATOR READY INDICATORHOW TO OPERATE ON-SCREEN MENU OPERATING ON-SCREEN MENUFLOW OF ON-SCREEN MENU WIRELESS REMOTE CONTROLSETTING MENU BEFORE OPERATION MENU BARMENU BAR IN COMPUTER MODE Press MENU BUTTON while in Computer mode MODE MENUVIEW MENU MENU BAR IN MCI MODEPress MENU BUTTON while in MCI mode Power off? BASIC OPERATIONSTURNING ON / OFF THE PROJECTOR TURNING ON THE PROJECTORADJUSTING THE IMAGE ZOOM ADJUSTMENTFOCUS ADJUSTMENT KEYSTONE ADJUSTMENTSOUND ADJUSTMENT SOUND VOLUME ADJUSTMENTSOUND MUTE ADJUSTMENT BASIC OPERATION NO SHOW FUNCTIONCOMPUTER MODE SELECTING COMPUTER MODESELECTING COMPUTER SYSTEM DIRECT OPERATIONPC ADJUSTMENT COMPUTER MODEReset Closes the PC ADJUST MenuTotal lines Total dotsMAC LC13 COMPUTER MODE COMPATIBLE COMPUTER SPECIFICATIONSNOTE Specifications are subject to change without notice PICTURE IMAGE ADJUSTMENT ADJUST PICTURE IMAGE MANUALLYNORMAL FUNCTION NormalPICTURE POSITION ADJUSTMENT COMPUTER MODE AUTO IMAGE FUNCTIONStarts the Auto Image Adjustment Closes the AUTO IMAGE ADJUSTMENT MenuPICTURE SCREEN ADJUSTMENT TrueKeystone Digital ZoomVIDEO MODE SELECTING VIDEO MODESELECTING COLOR SYSTEM RegularADJUSTING THE PICTURE IMAGE Closes the PICTURE IMAGE ADJUSTMENT MenuColor TintOPERATING THE PC CARD SLOT HOW TO LOAD THE MEMORY CARD INTO THE PROJECTORMCI MODE SELECTING MCI MODE AVAILABLE DATAAVAILABLE CARD Media Card ImagerSHOW THE DATA IN THE MEMORY CARD INDEX SELECTIONPAGE SELECTION Index and PageACCESS TO THE MEMORY CARD THROUGH THE PROJECTOR WRITE DATA INTO THE MEMORY CARDPICTURE IMAGE ADJUSTMENT ADJUST THE PICTURE IMAGE MANUALLYRecalls the data previously adjusted Stores the adjusted data in the memoryPICTURE SCREEN ADJUSTMENT IMPORTANT NOTE INSTALL / REMOVE THE SMARTMEDIASMARTMEDIA AND PC CARD ADAPTER MCI MODE PRECAUTIONS AND SPECIFICATIONS OF THE SMARTMEDIA PRECAUTIONS AND SPECIFICATIONS OF THE PC CARD ADAPTERSETTING SETTING MENUSELECTING LANGUAGE Blue backOPERATING WIRELESS MOUSE INSTALLATIONOPERATING WIRELESS MOUSE APPENDIXMAINTENANCE TEMPERATURE WARNING INDICATORAIR FILTER CARE AND CLEANING CLEANING THE PROJECTION LENSAPPENDIX LAMP REPLACEMENT INDICATOR LAMP REPLACEMENTLAMP REPLACEMENT MONITOR TIMER ORDER REPLACEMENT LAMPTry these Solution TROUBLESHOOTINGProblem Remote Control Unit TECHNICAL SPECIFICATIONS OPTIONAL PARTS Control Cable for Serial PortType No. POA-MCSRL Control Cable for ADB PortLIMITED WARRANTY WARRANTY LIMITATION AND EXCLUSIONDISCLAIMER OR UNSTATED WARRANTIES LIMITATION OR LIABILITY