BOXLIGHT XD-10m manual Manual Sync, Manual Tracking, Horizontal Position, Vertical Position

Page 28

U s i n g	t h e	P r o j e c t o r

NOTE: The Manual Sync, Manual Tracking, Horizontal Position and Vertical Position options are available only for analog computer sources. The projector sets these options automatically for digital computer and video sources, with no manual override.

20

Manual Sync

The projector adjusts signal synchronization automatically for most computers. But if the projected computer image looks fuzzy or streaked, try turning Auto image off then back on again. If the image still looks bad, try adjusting the signal synchronization manually:

1Turn Auto Image off.

2Highlight Manual sync, press menu/select, use the arrow but- tons to adjust Manual sync until the image is sharp and free of streaks, then press menu/select.

Manual Tracking

The projector adjusts tracking automatically to match the video signal from your computer. However, if the display shows evenly spaced, fuzzy, vertical lines or if the projected image is too wide or too narrow for the screen, try turning Auto Image off then back on again. If the image is still bad, try adjusting the tracking man- ually:

1Turn Auto image off.

2Highlight Manual tracking, press menu/select, use the arrow buttons to adjust Manual tracking until the fuzzy vertical bars are gone, then press menu/select.

Horizontal Position

Follow these steps to manually adjust the horizontal position:

1Turn Auto image off.

2Highlight Horizontal position, press menu/select, use the arrow buttons to adjust the Horizontal position, then press menu/select.

Positioning adjustments are saved when you turn off the projec- tor.

Vertical Position

Follow these steps to manually adjust the vertical position.

1Turn Auto image off.

2Highlight Vertical position, press menu/select, use the arrow buttons to adjust the Vertical position, then press menu/select.

Positioning adjustments are saved when you turn off the projec- tor.

Image 28

Contents Page FCC Warning Canada Safety CertificationsEN 55022 Warning Declaration of Conformity TrademarksPage Table of Contents Appendix IndexSafety Definitions Safety Symbols Safety InstructionsSafety Terms Customer Service Important Operating ConsiderationsImage Resolution IntroductionCompatibility Unpacking the ProjectorT r o d u c t i o n Usage Guidelines Warranty If You Need AssistanceSetting UP the Projector Make sure the projector and the computer are turned offT t i n g O j e c t o r Connecting a Computer Connecting a Video Player Powering up the Projector and Adjusting the Image Turning Off the ProjectorT t i n g O j e c t o r Basic Image Adjustment Using the ProjectorAdjusting the Projector I n g O j e c t o r Using the Remote Control Menu/select Using the Keypad and Remote ButtonsSource keypad only or Data and Video remote only Reset keypad only Keystone + remote onlyForward/back buttons remote only Up/down arrow buttonsUsing the On-Screen Menus Keystone Display MenuBrightness Contrast TintColor Blank screenResize Image Menu for Computer SourcesAuto Image Manual Sync Manual TrackingHorizontal Position Vertical PositionImage Menu for Video Sources Video Standard video sources onlyControl Menu Default SourceAuto Source Advanced Menu ResetRear Projection Language Menu Computer resolution Status MenuLamp hours used SourceI n g O j e c t o r Cleaning the Lens Maintenance & TroubleshootingReplacing the Projection Lamp Pull the yellow tab on the lamp module Loosen the captive screw on the lamp module I n t e n a n c e Troubleshooting Replacing the Batteries in the Remote Control Using the Security LockTroubleshooting Problem The projector is not running Problem Only the start-up screen displaysProblem Color or text not being projected Problem The screen resolution is not rightProblem Image isn’t centered on the screen Problem Image is too wide or narrow for screenProblem Image is noisy or streaked Problem Lamp seems to be getting dimmerProblem Lamp shuts off Call Boxlight at 1-800-762-5757 orSpecifications AppendixAccessories Standard Accessories ship with the projectorOptional Accessories Portable and Laptop Activation Chart Key command to Computer Activate port De-activate portFN-F6 FN-F4 FN-F1 NCR Wyse Software driven Zenith FN-F10 Using Video Mirroring with a PowerBook Computer Using SimulScanProjected Image Size Distance to screenDiagonal Maximum Minimum Image WidthIndex D e Page D e Limited Warranty Limitation of Liability