BOXLIGHT XD-10m manual Ncr

Page 49

	Key command to	Key command to
Computer	activate port	de-activate port

Micro Express*	automatic	warm reboot

Micron	FN-F2	FN-F2

Microslate*	automatic	warm reboot

Mitsubishi	SW2 On-Off-Off-Off	SW2 Off-On-On-On

NCR	setup screen option	setup screen option

NEC* **	setup screen option	setup screen option
	CRT at the DOS prompt	LCD at the DOS prompt
	FN-F3	FN-F3

Olivetti*	automatic	automatic

	FN-O/*	FN-O/*

Packard Bell* **	FN-F0	FN-F0

	Ctrl-Alt-<	Ctrl-Alt->

Panasonic	FN-F2	FN-F2

Prostar	Ctrl-Alt-S at bootup	Ctrl-Alt-S at bootup

Samsung*	setup screen option	setup screen option

Sanyo	setup screen option	setup screen option

Sharp	dip switch to CRT	dip switch to LCD

Sun SPARC-	Ctrl-Shift-M	Ctrl-Shift-M
Dataview

Tandy**	Ctrl-Alt-Insert	Ctrl-Alt-Insert
	setup screen option	setup screen option

Tangent	FN-F5	FN-F5

Texas Instru-	setup screen option	setup screen option
ments*

Top-Link* **	setup screen option	setup screen option
	FN-F6	FN-F6

Toshiba* **	Ctrl-Alt-End	Ctrl-Alt-Home
	FN-End	FN-Home
	FN-F5	FN-F5
	setup screen option	setup screen option

Twinhead*	FN-F7	FN-F7
	FN-F5	FN-F5
	Automatic	Automatic

WinBook	Ctrl-Alt-F10	Ctrl-Alt-F10

41

Image 49

Contents Page FCC Warning Canada Safety CertificationsEN 55022 Warning Trademarks Declaration of ConformityPage Table of Contents Index AppendixSafety Definitions Safety Symbols Safety InstructionsSafety Terms Important Operating Considerations Customer ServiceIntroduction Image ResolutionCompatibility Unpacking the ProjectorT r o d u c t i o n Usage Guidelines If You Need Assistance WarrantyMake sure the projector and the computer are turned off Setting UP the ProjectorT t i n g O j e c t o r Connecting a Computer Connecting a Video Player Turning Off the Projector Powering up the Projector and Adjusting the ImageT t i n g O j e c t o r Basic Image Adjustment Using the ProjectorAdjusting the Projector I n g O j e c t o r Using the Remote Control Menu/select Using the Keypad and Remote ButtonsSource keypad only or Data and Video remote only Keystone + remote only Reset keypad onlyForward/back buttons remote only Up/down arrow buttonsUsing the On-Screen Menus Keystone Display MenuBrightness Tint ContrastColor Blank screenResize Image Menu for Computer SourcesAuto Image Manual Tracking Manual SyncHorizontal Position Vertical PositionVideo Standard video sources only Image Menu for Video SourcesControl Menu Default SourceAuto Source Advanced Menu ResetRear Projection Language Menu Status Menu Computer resolutionLamp hours used SourceI n g O j e c t o r Cleaning the Lens Maintenance & TroubleshootingReplacing the Projection Lamp Pull the yellow tab on the lamp module Loosen the captive screw on the lamp module I n t e n a n c e Troubleshooting Using the Security Lock Replacing the Batteries in the Remote ControlProblem Only the start-up screen displays Troubleshooting Problem The projector is not runningProblem The screen resolution is not right Problem Color or text not being projectedProblem Image isn’t centered on the screen Problem Image is too wide or narrow for screenProblem Lamp seems to be getting dimmer Problem Image is noisy or streakedProblem Lamp shuts off Call Boxlight at 1-800-762-5757 orAppendix SpecificationsStandard Accessories ship with the projector AccessoriesOptional Accessories Key command to Computer Activate port De-activate port Portable and Laptop Activation ChartFN-F6 FN-F4 FN-F1 NCR Wyse Software driven Zenith FN-F10 Using SimulScan Using Video Mirroring with a PowerBook ComputerDistance to screen Projected Image SizeDiagonal Maximum Minimum Image WidthIndex D e Page D e Limited Warranty Limitation of Liability