BOXLIGHT XD-10m Maintenance & Troubleshooting, Cleaning the Lens, Replacing the Projection Lamp

Page 35

MAINTENANCE & TROUBLESHOOTING

This section describes how to:

•clean the lens

•replace the projection lamp

•replace the batteries in the remote

•use the security lock feature

•troubleshoot the projector

Cleaning the Lens

Follow these steps to clean the projection lens:

1Apply a non-abrasive camera lens cleaner to a soft, dry cloth.

•Avoid using an excessive amount of cleaner, and don’t apply the cleaner directly to the lens.

•Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.

2Lightly wipe the cleaning cloth over the lens in a circular motion.

3If you don’t intend to use the projector immediately, replace the lens cap.

Replacing the Projection Lamp

The lamp hour counter in the Status menu counts the number of hours the lamp has been in use. Change the lamp when the brightness is no longer acceptable. You can order new lamp mod- ules from BOXLIGHT. See “Accessories” on page 36 for informa- tion.

Follow these steps to replace the projection lamp:

1Turn off the projector and unplug the power cord.

2Wait 30 minutes to allow the projector to cool thoroughly.

WARNING: To avoid burns, allow the projector to cool for at least 30 minutes before you open the lamp access grill. Never extract the lamp module while the projector is operating.

27

Image 35

Contents Page EN 55022 Warning Safety CertificationsFCC Warning Canada Trademarks Declaration of ConformityPage Table of Contents Index AppendixSafety Terms Safety InstructionsSafety Definitions Safety Symbols Important Operating Considerations Customer ServiceUnpacking the Projector Image ResolutionIntroduction CompatibilityT r o d u c t i o n Usage Guidelines If You Need Assistance WarrantyMake sure the projector and the computer are turned off Setting UP the ProjectorT t i n g O j e c t o r Connecting a Computer Connecting a Video Player Turning Off the Projector Powering up the Projector and Adjusting the ImageT t i n g O j e c t o r Adjusting the Projector Using the ProjectorBasic Image Adjustment I n g O j e c t o r Using the Remote Control Source keypad only or Data and Video remote only Using the Keypad and Remote ButtonsMenu/select Up/down arrow buttons Reset keypad onlyKeystone + remote only Forward/back buttons remote onlyUsing the On-Screen Menus Brightness Display MenuKeystone Blank screen ContrastTint ColorAuto Image Image Menu for Computer SourcesResize Vertical Position Manual SyncManual Tracking Horizontal PositionVideo Standard video sources only Image Menu for Video SourcesAuto Source Default SourceControl Menu Rear Projection ResetAdvanced Menu Language Menu Source Computer resolutionStatus Menu Lamp hours usedI n g O j e c t o r Replacing the Projection Lamp Maintenance & TroubleshootingCleaning the Lens Pull the yellow tab on the lamp module Loosen the captive screw on the lamp module I n t e n a n c e Troubleshooting Using the Security Lock Replacing the Batteries in the Remote ControlProblem Only the start-up screen displays Troubleshooting Problem The projector is not runningProblem Image is too wide or narrow for screen Problem Color or text not being projectedProblem The screen resolution is not right Problem Image isn’t centered on the screenCall Boxlight at 1-800-762-5757 or Problem Image is noisy or streakedProblem Lamp seems to be getting dimmer Problem Lamp shuts offAppendix SpecificationsStandard Accessories ship with the projector AccessoriesOptional Accessories Key command to Computer Activate port De-activate port Portable and Laptop Activation ChartFN-F6 FN-F4 FN-F1 NCR Wyse Software driven Zenith FN-F10 Using SimulScan Using Video Mirroring with a PowerBook ComputerImage Width Projected Image SizeDistance to screen Diagonal Maximum MinimumIndex D e Page D e Limited Warranty Limitation of Liability