BenQ MP522, MP513 user manual Positioning your projector, Choosing a location

Page 13

Positioning your projector

Choosing a location

Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment.

Your projector is designed to be installed in one of four possible installation locations:

1. Front Table

Select this location with the projector placed near the floor in front of the screen. This is the most common way to position the projector for quick setup and portability.

2. Front Ceiling

Select this location with the projector suspended upside- down from the ceiling in front of the screen.

Purchase the BenQ Projector Ceiling Mounting Kit from your dealer to mount your projector on the ceiling.

Set Front Ceiling in the SYSTEM SETUP: Basic >

Projector Position menu after you turn the projector on.

3. Rear Table

Select this location with the projector placed near the floor behind the screen.

Note that a special rear projection screen is required.

Set Rear Table in the SYSTEM SETUP: Basic > Projector

Position menu after you turn the projector on.

4. Rear Ceiling

Select this location with the projector suspended upside- down from the ceiling behind the screen.

Note that a special rear projection screen and the BenQ Projector Ceiling Mounting Kit are required for this installation location.

Set Rear Ceiling in the SYSTEM SETUP: Basic >

Projector Position menu after you turn the projector on.

Positioning your projector

13

Image 13
Contents MP512/MP513/MP522 Digital Projector WelcomeTable of contents Refer servicing to qualified service personnel Important safety instructionsFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Do not block the ventilation holes Ceiling mounting the projector Introduction Projector featuresIntroduction Shipping contents Front/upper side Projector exterior viewRear/lower side External control panelProjector Controls and functionsRemote control Pull out the battery holder Remote control effective rangeChoosing a location Positioning your projectorObtaining a preferred projected image size Page MP513/MP522 projection dimensions 12000 457 MP512 projection dimensionsConnecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting a monitorBest video quality Connecting Video source devicesBetter video quality Least video qualityTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceAV device Video cable To connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationOperation Use / to highlight the System Setup Basic menu Using the menusSetting a password Utilizing the password functionIf you forget the password Security SettingsChanging the password Entering the password recall procedureDisabling the password function Enter a new passwordAdjusting the projected image Switching input signalAdjusting the projection angle Fine-tuning the image size and clarity Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsDisplays Press Image or pressUse of the screen without altering the images aspect Ratio Selecting the aspect ratioPicture modes for different types of signals Selecting a picture modePC input signals D-Sub / Comp. analog RGB Video input signals S-Video, Video, D-Sub / Comp. YPbPrFine-tuning the image quality in user modes Using Wall ColorSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Top-Left Bottom-Left Top- Right Bottom-Right Setting the presentation timerHow to use the Timer On key? To cancel the timer, perform the following stepsOr go to the System Setup Basic Panel Hiding the imageFreezing the image Utilizing FAQ functionOperating in a high altitude environment Shutting down the projector Personalizing the projector menu displayMenu system Menu operationMain menu Sub-menu Options Settings Power on lock On/Off System Setup AdvancedBasic SecurityDescription of each menu Temperature 3D Color Picture menu Source 4. System Setup menuBasic menuSave Settings TimerAuto Power System Setup Basic menu AdvancedBlank Timer Sleep TimerReset All System Setup Advanced menuStandby D Sub OutputFeatures Service FAQ-Image InstallationInformation menu CurrentCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourTiming of replacing the lamp Replacing the lamp Loosen the screw that secures the lamp MaintenanceMaintenance Setup Advanced Lamp Settings menu Resetting the lamp timerDisplays. Press to highlight Reset lamp Tighten the screw that secures the lampIndicators Troubleshooting Projector specifications SpecificationsResolution Horizontal Vertical Pixel Mode Frequency KHz MHz DimensionsMm W x 90 mm H x 214 mm D 255 61.5 15.73 59.94 15.73 Specifications31.47 59.94 15.63 50.00Limited warranty Warranty and Copyright informationFCC statement Regulation statements