BenQ MP522, MP513 user manual Regulation statements, FCC statement

Page 59

Regulation statements

FCC statement

CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the distance between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

EEC statement

This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electronic Magnetic Compatibility) and fulfills these requirements.

WEEE directive

Disposal of Waste Electrical and Electronic Equipment by users in private households in the European Union.

This symbol on the product or on the packaging indicates that this can not be disposed of as household waste. You must dispose of your waste equipment by handling it over to the applicable take-back scheme for the recycling of electrical and electronic equipment. For more information about recycling of this equipment, please contact your city office, the shop where you purchased the equipment or your household waste disposal service. The recycling of materials will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and environment.

Regulation statements

59

Image 59
Contents MP512/MP513/MP522 Digital Projector WelcomeTable of contents Do not look straight at the projector Important safety instructionsRefer servicing to qualified service personnel Future reference Projector lamp is onSafety Instructions Do not block the ventilation holes Ceiling mounting the projector Introduction Projector featuresIntroduction Shipping contents External control panel Projector exterior viewFront/upper side Rear/lower sideProjector Controls and functionsRemote control Pull out the battery holder Remote control effective rangeChoosing a location Positioning your projectorObtaining a preferred projected image size Page MP513/MP522 projection dimensions 12000 457 MP512 projection dimensionsTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionTo connect the projector to a monitor Connecting a monitorLeast video quality Connecting Video source devicesBest video quality Better video qualityTo connect the projector to a Component Video source device Connecting a Component Video source deviceAV device Video cable Connecting an S-Video source deviceTo connect the projector to an S-Video source device To connect the projector to a composite Video source device Connecting a composite Video source deviceOperation OperationStarting up the projector Use / to highlight the System Setup Basic menu Using the menusSecurity Settings Utilizing the password functionSetting a password If you forget the passwordEnter a new password Entering the password recall procedureChanging the password Disabling the password functionAdjusting the projection angle Switching input signalAdjusting the projected image Fine-tuning the image size and clarity Auto-adjusting the imageImage or press Magnifying and searching for detailsCorrecting keystone Displays PressUse of the screen without altering the images aspect Ratio Selecting the aspect ratioVideo input signals S-Video, Video, D-Sub / Comp. YPbPr Selecting a picture modePicture modes for different types of signals PC input signals D-Sub / Comp. analog RGBAdjusting Brightness Using Wall ColorFine-tuning the image quality in user modes Setting the User 1/User 2 modeAdjusting Brilliant Color Adjusting ColorAdjusting Tint Adjusting SharpnessPress Mode/Enter and the 3D Color Management page displays Top-Left Bottom-Left Top- Right Bottom-Right Setting the presentation timerHiding the image To cancel the timer, perform the following stepsHow to use the Timer On key? Or go to the System Setup Basic PanelOperating in a high altitude environment Utilizing FAQ functionFreezing the image Shutting down the projector Personalizing the projector menu displayMain menu Sub-menu Options Menu operationMenu system Security System Setup AdvancedSettings Power on lock On/Off BasicDescription of each menu Timer Picture menu Source 4. System Setup menuBasic menuTemperature 3D Color Save SettingsSleep Timer System Setup Basic menu AdvancedAuto Power Blank TimerSub Output System Setup Advanced menuReset All Standby DCurrent FAQ-Image InstallationFeatures Service Information menuCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as EconomicSetting Auto Power Off Lamp informationTiming of replacing the lamp Replacing the lamp Loosen the screw that secures the lamp MaintenanceMaintenance Tighten the screw that secures the lamp Resetting the lamp timerSetup Advanced Lamp Settings menu Displays. Press to highlight Reset lampIndicators Troubleshooting Projector specifications SpecificationsMm W x 90 mm H x 214 mm D 255 61.5 DimensionsResolution Horizontal Vertical Pixel Mode Frequency KHz MHz 15.63 50.00 15.73 Specifications15.73 59.94 31.47 59.94Limited warranty Warranty and Copyright informationFCC statement Regulation statements