BenQ MP522, MP513 user manual Connecting a Component Video source device

Page 21

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video output sockets available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a Component Video source device:

1.Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the Component Video output sockets of the Video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue, and red to red.

2.Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with

a D-Sub type connector) to the D-SUB IN socket on the projector.

The final connection path should be like that shown in the following diagram:

AV device

Component Video to VGA (D-

Sub) adaptor cable

If the selected video image is not displayed after the projector is turned on and the correct

video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

Connection 21

Image 21

Contents MP512/MP513/MP522 Digital Projector WelcomeTable of contents Refer servicing to qualified service personnel Important safety instructionsFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Do not block the ventilation holes Ceiling mounting the projector Projector features IntroductionIntroduction Shipping contents Front/upper side Projector exterior viewRear/lower side External control panelProjector Controls and functionsRemote control Pull out the battery holder Remote control effective rangeChoosing a location Positioning your projectorObtaining a preferred projected image size Page MP513/MP522 projection dimensions 12000 457 MP512 projection dimensionsConnecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting a monitorBest video quality Connecting Video source devicesBetter video quality Least video qualityTo connect the projector to a Component Video source device Connecting a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceAV device Video cable To connect the projector to a composite Video source device Connecting a composite Video source deviceOperation Starting up the projectorOperation Use / to highlight the System Setup Basic menu Using the menusSetting a password Utilizing the password functionIf you forget the password Security SettingsChanging the password Entering the password recall procedureDisabling the password function Enter a new passwordSwitching input signal Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsDisplays Press Image or pressUse of the screen without altering the images aspect Ratio Selecting the aspect ratioPicture modes for different types of signals Selecting a picture modePC input signals D-Sub / Comp. analog RGB Video input signals S-Video, Video, D-Sub / Comp. YPbPrFine-tuning the image quality in user modes Using Wall ColorSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Top-Left Bottom-Left Top- Right Bottom-Right Setting the presentation timerHow to use the Timer On key? To cancel the timer, perform the following stepsOr go to the System Setup Basic Panel Hiding the imageUtilizing FAQ function Freezing the imageOperating in a high altitude environment Shutting down the projector Personalizing the projector menu displayMenu operation Menu systemMain menu Sub-menu Options Settings Power on lock On/Off System Setup AdvancedBasic SecurityDescription of each menu Temperature 3D Color Picture menu Source 4. System Setup menuBasic menuSave Settings TimerAuto Power System Setup Basic menu AdvancedBlank Timer Sleep TimerReset All System Setup Advanced menuStandby D Sub OutputFeatures Service FAQ-Image InstallationInformation menu CurrentCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourTiming of replacing the lamp Replacing the lamp Loosen the screw that secures the lamp MaintenanceMaintenance Setup Advanced Lamp Settings menu Resetting the lamp timerDisplays. Press to highlight Reset lamp Tighten the screw that secures the lampIndicators Troubleshooting Projector specifications SpecificationsDimensions Resolution Horizontal Vertical Pixel Mode Frequency KHz MHzMm W x 90 mm H x 214 mm D 255 61.5 15.73 59.94 15.73 Specifications31.47 59.94 15.63 50.00Limited warranty Warranty and Copyright informationFCC statement Regulation statements