BenQ MP513, MP522 Setting the presentation timer, Top-Left Bottom-Left Top- Right Bottom-Right

Page 36

Setting the presentation timer

The presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function:

1.Press Timer Setup on the remote control or go to the SYSTEM SETUP: Basic > Presentation Timer menu and press Mode/Enter to display the Presentation Timer page.

2.Press to highlight Timer period and decide the timer period by pressing / . The length of time can be set from 1 to 5 minutes in 1- minute increments and 5 to 240 minutes in 5- minute increments.

If the timer is already on, the timer will restart whenever the Timer period is reset.

Presentation Timer

Timer period

 

 

 

 

 

 

Timer display

 

 

Always

Timer position

 

 

Top-Left

Timer counting direction

 

Count Down

On

Off

 

 

 

MENUBack

3.Press to highlight Timer display and choose if you want the timer to show up on the screen by pressing / .

Selection

Description

Always

Displays the timer on screen throughout the presentation time.

 

 

1 min/2 min/3 min

Displays the timer on screen in the last 1/2/3 minute(s).

 

 

Never

Hides the timer throughout the presentation time.

 

 

4.Press to highlight Timer position and set the timer position by pressing / .

Top-Left Bottom-Left Top- Right Bottom-Right

5 min

5 min

5 min

5 min

5.Press to highlight Timer counting direction and select your desired counting direction by pressing / .

Selection

Description

Count Up

Increases from 0 to the preset time.

 

 

Count Down

Decrease from the preset time to 0.

 

 

6.To activate the presentation timer, press and press / to select On and press Mode/Enter.

7.A confirmation message displays. Highlight Yes and press Mode/Enter to confirm. You will see the message “Timer is On” displaying on the screen. The timer starts counting at the time the timer is on.

NOTICE

Are you sure to turn on the presentation timer?

Yes No

36 Operation

Image 36
Contents Welcome MP512/MP513/MP522 Digital ProjectorTable of contents Important safety instructions Refer servicing to qualified service personnelFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Do not block the ventilation holes Ceiling mounting the projector Projector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper sideRear/lower side External control panelControls and functions ProjectorRemote control Remote control effective range Pull out the battery holderPositioning your projector Choosing a locationObtaining a preferred projected image size Page MP513/MP522 projection dimensions MP512 projection dimensions 12000 457Connecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computerConnecting a monitor To connect the projector to a monitorConnecting Video source devices Best video qualityBetter video quality Least video qualityConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceAV device Video cable Connecting a composite Video source device To connect the projector to a composite Video source deviceOperation Starting up the projectorOperation Using the menus Use / to highlight the System Setup Basic menuUtilizing the password function Setting a passwordIf you forget the password Security SettingsEntering the password recall procedure Changing the passwordDisabling the password function Enter a new passwordSwitching input signal Adjusting the projected imageAdjusting the projection angle Auto-adjusting the image Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneDisplays Press Image or pressSelecting the aspect ratio Use of the screen without altering the images aspect RatioSelecting a picture mode Picture modes for different types of signalsPC input signals D-Sub / Comp. analog RGB Video input signals S-Video, Video, D-Sub / Comp. YPbPrUsing Wall Color Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Setting the presentation timer Top-Left Bottom-Left Top- Right Bottom-RightTo cancel the timer, perform the following steps How to use the Timer On key?Or go to the System Setup Basic Panel Hiding the imageUtilizing FAQ function Freezing the imageOperating in a high altitude environment Personalizing the projector menu display Shutting down the projectorMenu operation Menu systemMain menu Sub-menu Options System Setup Advanced Settings Power on lock On/OffBasic SecurityDescription of each menu Picture menu Source 4. System Setup menuBasic menu Temperature 3D ColorSave Settings TimerSystem Setup Basic menu Advanced Auto PowerBlank Timer Sleep TimerSystem Setup Advanced menu Reset AllStandby D Sub OutputFAQ-Image Installation Features ServiceInformation menu CurrentMaintenance Care of the projectorSetting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Loosen the screw that secures the lamp Maintenance Replacing the lampMaintenance Resetting the lamp timer Setup Advanced Lamp Settings menuDisplays. Press to highlight Reset lamp Tighten the screw that secures the lampIndicators Troubleshooting Specifications Projector specificationsDimensions Resolution Horizontal Vertical Pixel Mode Frequency KHz MHzMm W x 90 mm H x 214 mm D 255 61.5 15.73 Specifications 15.73 59.9431.47 59.94 15.63 50.00Warranty and Copyright information Limited warrantyRegulation statements FCC statement