BenQ MP513, MP522 user manual Resetting the lamp timer, Tighten the screw that secures the lamp

Page 52

9.Tighten the screw that secures the lamp.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw.

10.Ensure the handle is fully laid flat and locked in place.

11.Replace the lamp cover on the projector.

12.Tighten the screws that secure the lamp

cover.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screws.

13.Restart the projector.

Do not turn the power on with the lamp cover removed.

Resetting the lamp timer

	14. After the startup logo, open the On-Screen	Notice
	Display (OSD) menu. Go to the SYSTEM
		Reset Lamp Timer?
	SETUP: Advanced > Lamp Settings menu.
	Press Mode/Enter. The Lamp Settings page	Reset	Cancel
	displays. Press to highlight Reset lamp

timer and press Mode/Enter. A warning

message displays asking if you want to reset the lamp timer. Highlight Reset and press Mode/Enter. The lamp time will be reset to '0'.

Do not reset if the lamp is not new or replaced as this could cause damage.

52 Maintenance

Image 52

Contents Welcome MP512/MP513/MP522 Digital ProjectorTable of contents Important safety instructions Refer servicing to qualified service personnelFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Do not block the ventilation holes Ceiling mounting the projector Introduction Projector featuresIntroduction Shipping contents Projector exterior view Front/upper sideRear/lower side External control panelControls and functions ProjectorRemote control Remote control effective range Pull out the battery holderPositioning your projector Choosing a locationObtaining a preferred projected image size Page MP513/MP522 projection dimensions MP512 projection dimensions 12000 457Connecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computerConnecting a monitor To connect the projector to a monitorConnecting Video source devices Best video qualityBetter video quality Least video qualityConnecting a Component Video source device To connect the projector to a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceAV device Video cable Connecting a composite Video source device To connect the projector to a composite Video source deviceStarting up the projector OperationOperation Using the menus Use / to highlight the System Setup Basic menuUtilizing the password function Setting a passwordIf you forget the password Security SettingsEntering the password recall procedure Changing the passwordDisabling the password function Enter a new passwordAdjusting the projected image Switching input signalAdjusting the projection angle Auto-adjusting the image Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneDisplays Press Image or pressSelecting the aspect ratio Use of the screen without altering the images aspect RatioSelecting a picture mode Picture modes for different types of signalsPC input signals D-Sub / Comp. analog RGB Video input signals S-Video, Video, D-Sub / Comp. YPbPrUsing Wall Color Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Setting the presentation timer Top-Left Bottom-Left Top- Right Bottom-RightTo cancel the timer, perform the following steps How to use the Timer On key?Or go to the System Setup Basic Panel Hiding the imageFreezing the image Utilizing FAQ functionOperating in a high altitude environment Personalizing the projector menu display Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options System Setup Advanced Settings Power on lock On/OffBasic SecurityDescription of each menu Picture menu Source 4. System Setup menuBasic menu Temperature 3D ColorSave Settings TimerSystem Setup Basic menu Advanced Auto PowerBlank Timer Sleep TimerSystem Setup Advanced menu Reset AllStandby D Sub OutputFAQ-Image Installation Features ServiceInformation menu CurrentMaintenance Care of the projectorSetting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Loosen the screw that secures the lamp Maintenance Replacing the lampMaintenance Resetting the lamp timer Setup Advanced Lamp Settings menuDisplays. Press to highlight Reset lamp Tighten the screw that secures the lampIndicators Troubleshooting Specifications Projector specificationsResolution Horizontal Vertical Pixel Mode Frequency KHz MHz DimensionsMm W x 90 mm H x 214 mm D 255 61.5 15.73 Specifications 15.73 59.9431.47 59.94 15.63 50.00Warranty and Copyright information Limited warrantyRegulation statements FCC statement