BenQ MP522, MP513 user manual Auto-adjusting the image, Fine-tuning the image size and clarity

Page 29

If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 30 for details.

Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

Be careful when you press the adjuster button as it is close to the exhaust vent where hot air comes from.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the upper left corner of the screen for 3 seconds.

• The screen will be blank while AUTO is functioning.

This function is only available when PC signal (analog RGB) is selected.

Fine-tuning the image size and clarity

1.Adjust the projected image to the size that

you need using the zoom ring. (Zoom ring is not available with the MP512.)

2.Then sharpen the image by rotating the focus ring.

Operation 29

Image 29
Contents MP512/MP513/MP522 Digital Projector WelcomeTable of contents Refer servicing to qualified service personnel Important safety instructionsFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Do not block the ventilation holes Ceiling mounting the projector Introduction Projector featuresIntroduction Shipping contents Front/upper side Projector exterior viewRear/lower side External control panelProjector Controls and functionsRemote control Pull out the battery holder Remote control effective rangeChoosing a location Positioning your projectorObtaining a preferred projected image size Page MP513/MP522 projection dimensions 12000 457 MP512 projection dimensionsConnecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting a monitorBest video quality Connecting Video source devicesBetter video quality Least video qualityTo connect the projector to a Component Video source device Connecting a Component Video source deviceAV device Video cable Connecting an S-Video source deviceTo connect the projector to an S-Video source device To connect the projector to a composite Video source device Connecting a composite Video source deviceOperation OperationStarting up the projector Use / to highlight the System Setup Basic menu Using the menusSetting a password Utilizing the password functionIf you forget the password Security SettingsChanging the password Entering the password recall procedureDisabling the password function Enter a new passwordAdjusting the projection angle Switching input signalAdjusting the projected image Fine-tuning the image size and clarity Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsDisplays Press Image or pressUse of the screen without altering the images aspect Ratio Selecting the aspect ratioPicture modes for different types of signals Selecting a picture modePC input signals D-Sub / Comp. analog RGB Video input signals S-Video, Video, D-Sub / Comp. YPbPrFine-tuning the image quality in user modes Using Wall ColorSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Top-Left Bottom-Left Top- Right Bottom-Right Setting the presentation timerHow to use the Timer On key? To cancel the timer, perform the following stepsOr go to the System Setup Basic Panel Hiding the imageOperating in a high altitude environment Utilizing FAQ functionFreezing the image Shutting down the projector Personalizing the projector menu displayMain menu Sub-menu Options Menu operationMenu system Settings Power on lock On/Off System Setup AdvancedBasic SecurityDescription of each menu Temperature 3D Color Picture menu Source 4. System Setup menuBasic menuSave Settings TimerAuto Power System Setup Basic menu AdvancedBlank Timer Sleep TimerReset All System Setup Advanced menuStandby D Sub OutputFeatures Service FAQ-Image InstallationInformation menu CurrentCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourTiming of replacing the lamp Replacing the lamp Loosen the screw that secures the lamp MaintenanceMaintenance Setup Advanced Lamp Settings menu Resetting the lamp timerDisplays. Press to highlight Reset lamp Tighten the screw that secures the lampIndicators Troubleshooting Projector specifications SpecificationsMm W x 90 mm H x 214 mm D 255 61.5 DimensionsResolution Horizontal Vertical Pixel Mode Frequency KHz MHz 15.73 59.94 15.73 Specifications31.47 59.94 15.63 50.00Limited warranty Warranty and Copyright informationFCC statement Regulation statements