BenQ MX761 user manual Remote control, Test, Auto, Keystone/Arrow buttons / Up Down

Page 11

Remote control

1
2	12
	13
3	14
4
	15
5	16
6
	15
7	17
8	18
9	19
	20
10

11	21
11
	22
	23

1.ON/OFF

Toggles the projector between standby mode and on.

2.Source selection buttons (COMPUTER-1, COMPUTER-2, VIDEO, S-VIDEO)

Selects an input source for display.

3.MENU/EXIT

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

4.BLANK

Used to hide the screen image.

5. Left/

Starts the FAQ function.

6.MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display (OSD) menu item.

7.LASER

Emits visible laser pointer light for presentation purposes.

8.PAGE UP/PAGE DOWN

Operates your display software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint).

9.FREEZE

Freezes the projected image.

10.NETWORK SETTING

Enters network setting directly.

11.TEST

Displays the test pattern.

12.NETWORK

Searches the network signal and project it within a few seconds once available.

13.SOURCE

Displays the source selection bar.

14.AUTO

Automatically determines the best picture timings for the displayed image.

15.Keystone/Arrow buttons ( / Up, /

Down)

Manually corrects distorted images resulting from an angled projection.

16. Right/

Locks the buttons on the projector.

When the On-Screen Display (OSD) menu is activated, the #5, #15 and #16 buttons are used as directional arrows to select the desired menu items and to make adjustments.

Introduction 11

Image 11

Contents MX760/MX761 Digital Projector WelcomeTable of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedIntroduction Projector featuresIntroduction Shipping contents Rear/lower side Projector exterior viewLeft Power indicator lightFocus ring Zoom ringKeystone/Arrow buttons / Up Down Remote controlTest AutoNumeric buttons Operating the Laser pointerMute MIC/VOL +Approx.+15º Remote control effective rangeReplacing the remote control batteries Front Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsShifting the projection lens When the projector position is fixedVideo cable Hdmi cable Connection ConnectionBest Connecting video source devicesConnecting audio Terminal name Terminal appearanceDevice Playing sound through the projectorAbout the microphone input Page Operation OperationStarting up the projector Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsScreen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color ManagementSelection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count DownHiding the image Utilizing FAQ functionRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeUsing the remote control Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeIf you are in a non-DHCP environment Controlling the projector through a LAN environmentCable connection If you are in a Dhcp environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Operation Operation Presenting from a USB Reader Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Basic Menu operationMenu system Main menu Sub-menu OptionsAdvanced Advanced Network Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Management Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsLock Settings Security DescriptionPanel Key BackgroundTest Pattern System Setup Advanced menu Function DescriptionReset All Baud RateStatus Features ServiceCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Tighten the screw that secures the lamp Tighten the screw that secures the lamp cover Connect the power and restart the projectorResetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsUnit mm DimensionsMm W x 128 mm H x 252 mm D Ceiling Mount screw M4 x 8 Max L = 8 mmSupported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Horizontal Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs TimingDisclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement for United States users EEC statement for European users