BenQ MX761 user manual If you forget the password, Entering the password recall procedure

Page 26
Password Error
Please try again.

If you forget the password

If the password function is activated, you will be asked to enter the six-digit password every time you turn on the projector. If you enter the wrong password, the password error message as pictured to the right is displayed lasting for 3 seconds, and the INPUT PASSWORD message follows. You can retry by entering another six-digit password, or if you did not record the

password in this manual, and you absolutely do not remember it, you can use the password recall procedure. See "Entering the password recall procedure" on page 26 for details.

If you enter an incorrect password 5 times in succession, the projector will automatically shut down in a short time.

Entering the password recall procedure

1.Press and hold AUTO on the projector or remote control for 3 seconds. The projector will display a coded number on the screen.

2.Write down the number and turn off your projector.

3.Seek help from the local BenQ service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.

RECALL PASSWORD

Please write down the recall code, and contact BenQ

Customer Center.

Recall Code: 0 2 1 2

MENU Exit

Changing the password

1.Open the OSD menu and go to the SYSTEM SETUP: Advanced> Security Settings > Change Password menu.

2.Press MODE/ENTER. The message “INPUT CURRENT PASSWORD” appears.

3.Enter the old password.

i.If the password is correct, another message “INPUT NEW PASSWORD” is displayed.

ii.If the password is incorrect, the password error message is displayed lasting for three seconds, and the message “INPUT CURRENT PASSWORD” is displayed for your retry. You can press MENU/EXIT to cancel the change or try another password.

4.Enter a new password.

IMPORTANT: The digits being input will be displayed as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this manual in a safe place.

5.Confirm the new password by re-entering the new password.

6.You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started.

7.To leave the OSD menu, press MENU/EXIT.

26 Operation

Image 26
Contents Welcome MX760/MX761 Digital ProjectorTable of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Rear/lower sideZoom ring Power indicator lightFocus ring LeftAuto Remote controlTest Keystone/Arrow buttons / Up DownMIC/VOL + Operating the Laser pointerMute Numeric buttonsApprox.+15º Remote control effective rangeReplacing the remote control batteries Front Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeWhen the projector position is fixed Shifting the projection lensConnection Video cable Hdmi cable ConnectionTerminal name Terminal appearance Connecting video source devicesConnecting audio BestDevice Playing sound through the projectorAbout the microphone input Page Operation OperationStarting up the projector Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERChanging the password If you forget the passwordEntering the password recall procedure Write down the number and turn off your projectorDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratioSetting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projectedCount Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionFreezing the image Utilizing FAQ functionRemote paging operations Hiding the imageLocking control keys To activate the High Altitude ModeUsing the remote control Operating in a high altitude environmentAdjusting the microphone volume Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneIf you are in a Dhcp environment Controlling the projector through a LAN environmentCable connection If you are in a non-DHCP environmentWireless connection Highlight Wireless LAN and press MODE/ENTERControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Operation Operation Presenting from a USB Reader Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Main menu Sub-menu Options Menu operationMenu system BasicAdvanced Advanced Network Description of each menu Management Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSettings System Setup Basic menu Function Description Quick AutoTimer SearchBackground Settings Security DescriptionPanel Key LockBaud Rate System Setup Advanced menu Function DescriptionReset All Test PatternSystem Features ServiceCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Tighten the screw that secures the lamp Tighten the screw that secures the lamp cover Connect the power and restart the projectorResetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsCeiling Mount screw M4 x 8 Max L = 8 mm DimensionsMm W x 128 mm H x 252 mm D Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs HorizontalCopyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement for European users Regulation statementsFCC statement for United States users Weee directive