BenQ MX761 user manual Warranty and Copyright information, Limited warranty, Disclaimer, Patents

Page 75

Warranty and Copyright information

Limited warranty

BenQ warrants this product against any defects in material and workmanship, under normal usage and storage.

Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, BenQ's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included). To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects.

Important: The above warranty shall be void if the customer fails to operate the product in accordance with BenQ's written instructions, especially the ambient humidity must be in- between 10% and 90%, temperature in-between 0°C and 35°C, altitude lower than 4920 feet, and avoiding to operate the projector in a dusty environment. This warranty gives you specific legal rights, and you may have other rights which vary from country to country.

For other information, please visit www.BenQ.com.

Copyright

Copyright 2010 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation.

Disclaimer

BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others are copyrights of their respective companies or organizations.

Patents

This BenQ projector is covered by the following patents:

U.S. patents 6,837,608; 7,275,834; 7,181,318. TW patents 202690; 205470; I228635; I259932. China patents ( 中国发明专利 ) ZL01143168.7; ZL03119907.0; ZL200510051609.2

Warranty and Copyright information

75

Image 75

Contents MX760/MX761 Digital Projector WelcomeTable of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedProjector features IntroductionIntroduction Shipping contents Rear/lower side Projector exterior viewLeft Power indicator lightFocus ring Zoom ringKeystone/Arrow buttons / Up Down Remote controlTest AutoNumeric buttons Operating the Laser pointerMute MIC/VOL +Remote control effective range Replacing the remote control batteriesApprox.+15º Front Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsShifting the projection lens When the projector position is fixedVideo cable Hdmi cable Connection ConnectionBest Connecting video source devicesConnecting audio Terminal name Terminal appearancePlaying sound through the projector About the microphone inputDevice Page Operation Starting up the projectorOperation Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsScreen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color ManagementSelection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count DownHiding the image Utilizing FAQ functionRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeUsing the remote control Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeIf you are in a non-DHCP environment Controlling the projector through a LAN environmentCable connection If you are in a Dhcp environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Basic Menu operationMenu system Main menu Sub-menu OptionsAdvanced Advanced Network Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Management Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsLock Settings Security DescriptionPanel Key BackgroundTest Pattern System Setup Advanced menu Function DescriptionReset All Baud RateStatus Features ServiceCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Tighten the screw that secures the lamp Connect the power and restart the projector Resetting the lamp timerTighten the screw that secures the lamp cover Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsUnit mm DimensionsMm W x 128 mm H x 252 mm D Ceiling Mount screw M4 x 8 Max L = 8 mmSupported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Horizontal Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs TimingDisclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement for United States users EEC statement for European users