BenQ MX761 Do not step on the projector or place, Any objects upon it. Besides probable, Injury

Page 6

Safety Instructions (Continued)

17.

Do not step on the projector or place

Ceiling mounting the projector

 

any objects upon it. Besides probable

 

 

 

physical damage to the projector, doing

We want you to have a pleasant

 

so may result in accidents and possible

experience using your BenQ projector,

 

injury.

so we need to bring this safety matter to

 

 

your attention to prevent possible

 

 

damage to person and property.

 

 

If you intend to mount your projector

 

 

on the ceiling, we strongly recommend

 

 

that you use a proper fitting BenQ

 

 

projector ceiling mount kit and that

 

 

you ensure it is securely and safely

 

 

installed.

18.

Do not place liquids near or on the

If you use a non-BenQ brand projector

ceiling mount kit, there is a safety risk

 

projector. Liquids spilled into the

 

that the projector may fall from the

 

projector may cause it to fail. If the

 

ceiling due to an improper attachment

 

projector does become wet, disconnect

 

through the use of the wrong gauge or

 

it from the power supply's power outlet

 

length screws.

 

and call BenQ to have the projector

 

You can purchase a BenQ projector

 

serviced.

 

ceiling mount kit from the place you

 

 

 

 

purchased your BenQ projector. BenQ

 

 

recommends that you also purchase a

 

 

separate Kensington lock compatible

 

 

security cable and attach it securely to

 

 

both the Kensington lock slot on the

 

 

projector and the base of the ceiling

 

 

mount bracket. This will perform the

 

 

secondary role of restraining the

 

 

projector should its attachment to the

19. This product is capable of displaying

mounting bracket become loose.

 

inverted images for ceiling mount

 

 

installation.

Hg - Lamp contains mercury. Manage in

 

Use only BenQ's Ceiling Mount Kit for

accordance with local disposal laws.

 

mounting the projector and ensure it is

See www.lamprecycle.org.

 

securely installed.

 

20.This apparatus must be earthed.

6 Important safety instructions

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Welcome MX760/MX761 Digital ProjectorTable of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeProjector features IntroductionIntroduction Shipping contents Projector exterior view Rear/lower sideZoom ring Power indicator lightFocus ring LeftAuto Remote controlTest Keystone/Arrow buttons / Up DownMIC/VOL + Operating the Laser pointerMute Numeric buttonsRemote control effective range Replacing the remote control batteriesApprox.+15º Front Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeWhen the projector position is fixed Shifting the projection lensConnection Video cable Hdmi cable ConnectionTerminal name Terminal appearance Connecting video source devicesConnecting audio BestPlaying sound through the projector About the microphone inputDevice Page Operation Starting up the projectorOperation Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERChanging the password If you forget the passwordEntering the password recall procedure Write down the number and turn off your projectorDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratioSetting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projectedCount Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionFreezing the image Utilizing FAQ functionRemote paging operations Hiding the imageLocking control keys To activate the High Altitude ModeUsing the remote control Operating in a high altitude environmentAdjusting the microphone volume Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneIf you are in a Dhcp environment Controlling the projector through a LAN environmentCable connection If you are in a non-DHCP environmentWireless connection Highlight Wireless LAN and press MODE/ENTERControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Main menu Sub-menu Options Menu operationMenu system BasicAdvanced Advanced Network Description of each menu Management Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSettings System Setup Basic menu Function Description Quick AutoTimer SearchBackground Settings Security DescriptionPanel Key LockBaud Rate System Setup Advanced menu Function DescriptionReset All Test PatternSystem Features ServiceCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Tighten the screw that secures the lamp Connect the power and restart the projector Resetting the lamp timerTighten the screw that secures the lamp cover Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsCeiling Mount screw M4 x 8 Max L = 8 mm DimensionsMm W x 128 mm H x 252 mm D Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs HorizontalCopyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement for European users Regulation statementsFCC statement for United States users Weee directive
Top Page Image Contents