BenQ MX761 user manual Switching input signal, Changing Color Space

Page 28

Switching input signal

The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. When starting up, the projector automatically searches for the available signals.

Be sure the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals.

To select the source:

•Using the remote control or projector

Press one of the Source buttons on the remote control, or press SOURCE on the projector repeatedly until your desired signal is selected.

•Using the OSD menu

1.Press SOURCE on the projector or remote control. A source selection bar is displayed.

2.Press / until your desired signal is selected and press MODE/ENTER.

Once detected, the selected source information will be displayed at the corner of the screen for seconds. If there is multiple equipment connected to the projector, repeat steps 1-2to search for another signal.

•The brightness level of the projected image will change accordingly when you switch between different input signals. Data (graphic) "PC" presentations using mostly static images are generally brighter than "Video" using mostly moving images (movies).

Computer1/YPbPr1

Computer2/YPbPr2

HDMI

Video

S-Video

Network Display

USB Display

USB Reader

•The native display resolution of this projector is in a 4:3 aspect ratio. For best display picture results, you should select and use an input signal which outputs at this resolution. Any other resolutions will be scaled by the projector depending upon the “aspect ratio” setting, which may cause some image distortion or loss of picture clarity. See "Selecting the aspect ratio" on page 29 for details.

•Firewall in the PC must be switched off to allow Q Presenter and USB Display to work.

Changing Color Space

In the unlikely event that you connect the projector to a DVD player via the projector’s HDMI input and the projected picture displays wrong colors, please change the color space to YUV.

To do this:

1.Press MENU/EXIT and then press / until the SOURCE menu is highlighted.

2.Press to highlight Color Space Conversion and press / to select a suitable color space.

This function is only available when the HDMI-input port is in use.

28 Operation

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Welcome MX760/MX761 Digital ProjectorTable of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Rear/lower sidePower indicator light Focus ringZoom ring LeftRemote control TestAuto Keystone/Arrow buttons / Up DownOperating the Laser pointer MuteMIC/VOL + Numeric buttonsReplacing the remote control batteries Remote control effective rangeApprox.+15º Positioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeWhen the projector position is fixed Shifting the projection lensConnection Video cable Hdmi cable ConnectionConnecting video source devices Connecting audioTerminal name Terminal appearance BestAbout the microphone input Playing sound through the projectorDevice Page Starting up the projector OperationOperation Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureChanging the password Write down the number and turn off your projectorDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioProjectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratioUsing Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projectedSetting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection DescriptionUtilizing FAQ function Remote paging operationsFreezing the image Hiding the imageTo activate the High Altitude Mode Using the remote controlLocking control keys Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelAdjusting the microphone volume Turning off the Power On/Off Ring ToneControlling the projector through a LAN environment Cable connectionIf you are in a Dhcp environment If you are in a non-DHCP environmentWireless connection Highlight Wireless LAN and press MODE/ENTERControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Menu operation Menu systemMain menu Sub-menu Options BasicAdvanced Advanced Network Description of each menu Picture Mode TemperatureManagement Save Settings Display menu Picture menu Function Description TeachingSystem Setup Basic menu Function Description Quick Auto TimerSettings SearchSettings Security Description Panel KeyBackground LockSystem Setup Advanced menu Function Description Reset AllBaud Rate Test PatternFeatures Service CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Tighten the screw that secures the lamp Resetting the lamp timer Connect the power and restart the projectorTighten the screw that secures the lamp cover Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Mm W x 128 mm H x 252 mm DCeiling Mount screw M4 x 8 Max L = 8 mm Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming HorizontalWarranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statement for United States usersEEC statement for European users Weee directive
Top Page Image Contents