BenQ MX761 user manual Features Service, Current, System, Status

Page 61

6. INFORMATION menu

Function

Description

FAQ-Image

 

and

 

Installation

Displays possible solutions to problems you may encounter.

 

FAQ-

 

Features and

 

Service

 

 

 

 

Source

 

Shows the current signal source.

 

Picture Mode

 

Shows the selected mode in the PICTURE menu.

Current

Resolution

Shows the native resolution of the input signal.

System

Color System

Status

Shows input system format: NTSC, PAL, SECAM, YUV, or RGB.

 

 

Equivalent Lamp Hour

 

Displays the number of hours the lamp has been used.

 

Firmware Version

 

Shows the firmware version of your projector.

 

 

Operation 61

Page 60 Page 62
Image 61
Page 60 Page 62
Contents MX760/MX761 Digital Projector WelcomeTable of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceIt from the power supplys power outlet InstalledServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Rear/lower side Projector exterior viewFocus ring Power indicator lightZoom ring LeftTest Remote controlAuto Keystone/Arrow buttons / Up DownMute Operating the Laser pointerMIC/VOL + Numeric buttonsReplacing the remote control batteries Remote control effective rangeApprox.+15º Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsShifting the projection lens When the projector position is fixedVideo cable Hdmi cable Connection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance BestAbout the microphone input Playing sound through the projectorDevice Page Starting up the projector OperationOperation Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Utilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordChanging the password Write down the number and turn off your projectorDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAdjustments Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratioSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Every adjustment made will reflect to Press To highlight Saturation and adjust its3D Color Management Range at 0, only pure red in the projectedTo cancel the timer, perform the following steps Setting the presentation timerCount Up Increases from 0 to the preset time Count Down Selection DescriptionRemote paging operations Utilizing FAQ functionFreezing the image Hiding the imageUsing the remote control To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentAdjusting the sound level Adjusting the soundAdjusting the microphone volume Turning off the Power On/Off Ring ToneCable connection Controlling the projector through a LAN environmentIf you are in a Dhcp environment If you are in a non-DHCP environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Menu system Menu operationMain menu Sub-menu Options BasicAdvanced Advanced Network Description of each menu Temperature Picture ModeManagement Save Settings Display menu Picture menu Function Description TeachingTimer System Setup Basic menu Function Description Quick AutoSettings SearchPanel Key Settings Security DescriptionBackground LockReset All System Setup Advanced menu Function DescriptionBaud Rate Test PatternCurrent Features ServiceSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Tighten the screw that secures the lamp Resetting the lamp timer Connect the power and restart the projectorTighten the screw that secures the lamp cover Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsMm W x 128 mm H x 252 mm D DimensionsCeiling Mount screw M4 x 8 Max L = 8 mm Unit mmSupported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming HorizontalLimited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement for United States users Regulation statementsEEC statement for European users Weee directive
Top Page Image Contents