BenQ MX761 user manual Timing of replacing the lamp, Status Message

Page 64

Timing of replacing the lamp

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

Go to http://lamp.benq.com for a replacement lamp.

The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 68 for details.

The following Lamp warning displays will remind you to change the lamp.

Status

Message

Install a new lamp for optimal performance. If the

Notice

projector is normally run with Economic selected

 

(See "Getting to know the lamp hour" on page 63),

Order Replacement Lamp

you may continue to operate the projector until

Lamp>XXXX Hours

the next hour lamp warning appears.

 

Press ENTER to dismiss the message.

Order a new lamp at lamp.benq.com

 

 

OK

 

 

It is strongly recommended that you replace the

Notice

lamp at this age. The lamp is a consumable item.

 

The lamp brightness diminishes with use. This is

Order Replacement Lamp

normal lamp behavior. You can replace the lamp

Lamp>XXXX Hours

whenever you notice that the brightness level has

 

significantly diminished.

Order a new lamp at lamp.benq.com

Press ENTER to dismiss the message.

OK

 

 

The lamp MUST be replaced before the projector

WARNING

will operate normally.

 

Press ENTER to dismiss the message.

Out of Lamp Usage Time

 

 

Replace lamp (refer to User Manual)

 

Then reset lamp timer

 

Order a new lamp at lamp.benq.com

 

OK

 

 

"XXXX" shown in the above messages are numbers that vary depending on different models.

64 Maintenance

Page 63 Page 65
Image 64
Page 63 Page 65
Contents Welcome MX760/MX761 Digital ProjectorTable of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Rear/lower sidePower indicator light Focus ringZoom ring LeftRemote control TestAuto Keystone/Arrow buttons / Up DownOperating the Laser pointer MuteMIC/VOL + Numeric buttonsReplacing the remote control batteries Remote control effective rangeApprox.+15º Positioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeWhen the projector position is fixed Shifting the projection lensConnection Video cable Hdmi cable ConnectionConnecting video source devices Connecting audioTerminal name Terminal appearance BestAbout the microphone input Playing sound through the projectorDevice Page Starting up the projector OperationOperation Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureChanging the password Write down the number and turn off your projectorDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioProjectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratioUsing Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projectedSetting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection DescriptionUtilizing FAQ function Remote paging operationsFreezing the image Hiding the imageTo activate the High Altitude Mode Using the remote controlLocking control keys Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelAdjusting the microphone volume Turning off the Power On/Off Ring ToneControlling the projector through a LAN environment Cable connectionIf you are in a Dhcp environment If you are in a non-DHCP environmentWireless connection Highlight Wireless LAN and press MODE/ENTERControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Menu operation Menu systemMain menu Sub-menu Options BasicAdvanced Advanced Network Description of each menu Picture Mode TemperatureManagement Save Settings Display menu Picture menu Function Description TeachingSystem Setup Basic menu Function Description Quick Auto TimerSettings SearchSettings Security Description Panel KeyBackground LockSystem Setup Advanced menu Function Description Reset AllBaud Rate Test PatternFeatures Service CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Tighten the screw that secures the lamp Resetting the lamp timer Connect the power and restart the projectorTighten the screw that secures the lamp cover Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Mm W x 128 mm H x 252 mm DCeiling Mount screw M4 x 8 Max L = 8 mm Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming HorizontalWarranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statement for United States usersEEC statement for European users Weee directive
Top Page Image Contents