BenQ MX761 user manual Video cable Hdmi cable Connection

Page 17

Connection

When connecting a signal source to the projector, be sure to:

1.Turn all equipment off before making any connections.

2.Use the correct signal cables for each source.

3.Ensure the cables are firmly inserted.

•In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 8). They are commercially available from electronics stores.

•The connection illustrations below are for reference only. The rear connecting jacks available on the projector vary with each projector model.

Monitor	Notebook or desktop
	computer

A/V device

										Microphone
(VGA)		(DVI)
1	2	3	1	8						Speakers	8 9



				11	4	8	5	6	7
				11	4	8	5	6	7

10or

RS-232

LAN

TYPE-A

USB

VIDEO

AUDIO-OUT

1.	VGA cable	6.	Video cable
2.	VGA to DVI-A cable	7.	Audio L/R cable
3.	USB cable	8.	Audio cable
4.	Component Video to VGA (D-Sub)	9.	Microphone
	adapter cable	10.	USB flash drive/USB wireless dongle
5.	S-Video cable	11.	HDMI cable

Connection 17

Image 17

Contents MX760/MX761 Digital Projector WelcomeTable of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceIt from the power supplys power outlet InstalledServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Rear/lower side Projector exterior viewFocus ring Power indicator lightZoom ring LeftTest Remote controlAuto Keystone/Arrow buttons / Up DownMute Operating the Laser pointerMIC/VOL + Numeric buttonsApprox.+15º Remote control effective rangeReplacing the remote control batteries Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsShifting the projection lens When the projector position is fixedVideo cable Hdmi cable Connection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance BestDevice Playing sound through the projectorAbout the microphone input Page Operation OperationStarting up the projector Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Utilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordChanging the password Write down the number and turn off your projectorDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAdjustments Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratioSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Every adjustment made will reflect to Press To highlight Saturation and adjust its3D Color Management Range at 0, only pure red in the projectedTo cancel the timer, perform the following steps Setting the presentation timerCount Up Increases from 0 to the preset time Count Down Selection DescriptionRemote paging operations Utilizing FAQ functionFreezing the image Hiding the imageUsing the remote control To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentAdjusting the sound level Adjusting the soundAdjusting the microphone volume Turning off the Power On/Off Ring ToneCable connection Controlling the projector through a LAN environmentIf you are in a Dhcp environment If you are in a non-DHCP environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Operation Operation Presenting from a USB Reader Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Menu system Menu operationMain menu Sub-menu Options BasicAdvanced Advanced Network Description of each menu Temperature Picture ModeManagement Save Settings Display menu Picture menu Function Description TeachingTimer System Setup Basic menu Function Description Quick AutoSettings SearchPanel Key Settings Security DescriptionBackground LockReset All System Setup Advanced menu Function DescriptionBaud Rate Test PatternCurrent Features ServiceSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Tighten the screw that secures the lamp Tighten the screw that secures the lamp cover Connect the power and restart the projectorResetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsMm W x 128 mm H x 252 mm D DimensionsCeiling Mount screw M4 x 8 Max L = 8 mm Unit mmSupported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming HorizontalLimited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement for United States users Regulation statementsEEC statement for European users Weee directive

Connection

S-Video cable

HDMI cable

Connection 17