Barco R9001490 owner manual Safety Area around the Projector

Page 18

Installation Guidelines

Warning on Rotating the Projector

When the lamp casing is installed, it is not allowed to rotate the projector clockwise when facing the lenses. An internal tilt switch will provide to start up the projector.

Correct way of rotating the projector, see image 6a.

Image 6

Image 6a

Safety Area around the Projector

Make sure the projector is located so that the air inlets and outlets for the cooling system are not obstructed. Leave a safety areo of about 1 meter on the left and the right side of the projector.

IR OUT

AIR IN

Safety area for air in & out

Image 7

Installation of the Lamp Casing

Lamp Casing Warnings

Never transport the projector with the lamp casing installed.

The lamp casing should always been transported in a vertical way to avoid damaging the lamp.

Never attempt to disassemble the lamp from its housing or to dispose of it other than by returning it to BARCO. Due to its high internal pressure, the lamp may explode in either hot or cold state.

3-4		5976072 BARCO ELM R12 17102000

Image 18

Contents Barco Projection Systems Barco n.v./Projection Systems Table of Contents Connections Start UP of the Adjustment Mode Installation Mode 10-1 Table of Contents To prevent personel injury SafetyTo prevent battery explosion To prevent projector damageSafety Packaging and Dimensions Dimensions Front ViewSide View Packaging and Dimensions Installation Guidelines Installation GuidelinesWhat image size? How big should the image be? Table/Top side facing ceiling Safety Area around the Projector Installing the projection lamp When transporting the projector Which Lens has to be selected Installing the Projection Lens 310a.DRW Stacking two Projectors Optional Profile Sections Connections AC Power mains cord connectionSwitching on FusesConnections Lamp Run Time Indication Switching to Stand-bySwitching Off Lamp Runtime WarningInput facilities Input facilities, RCVDS05 or VS05 connectedConnections Input module insertion into the projector Connections Fixed RGB analog input slot How to select input SlotHow to change the input slot setting Range of interfaces made by BarcoWhich signals can be connected to slot 2 ? Fixed 5-Input Slot slotHow to select What can be connected to the Video input ?What can be connected to the S-Video input ? Connections How to set the input priority ? Straps on module levelRemark How to select the RGB inputWhat can be connected to these inputs ? Sync selection on the Input Slots menuRGB-SOG How to select the Component Video input Indication on the input slot menu16HSDRUP How to select the RGB3S input Floating OrdwlqjruqrqiordwlqjlqsxwHow to select the Digital input What can be connected to this input ?Connections Connections How to select the Digital input Connections Connecting a VS05 to the projector Connecting an IR Remote Receiver to the projectorGetting Started Getting StartedGetting Started Terminology RCULamp Run Time Warning Quick Language Change ServiceGetting Started Lamp Light Output Indication Change LanguageLens Adjustment Shift Getting Started Quick Lens AdjustmentLens Adjustment ZOOM/FOCUS TiltOSD Color Getting Started Quick On Screen Color changePointing to the reflective screen OSD Color Highlighted ItemGetting Started Hardwired Remote Input Hardwired to the XLR InputHow to control the projector or projectors ? Why a projector address ?Set up an Individual Projector Address Before using the RCUInput Selection How to Program an Address into the RCU ?Getting Started Display the Projector Address on the Screen Picture ContolsPause key Stand-by keyEntering the Password Start up of the Adjustment ModePasswordProtection Start upSetting Up the personalised Passwords Menus on Local LCD DisplayRandom Access Adjustment Mode Overview FlowchartStarting up Possible File Manipulations Connecting a new SourceStart up the File Service File AnnotationImage is not perfect ? How to load a file ?Start up the Load File Load FileHow to change the settings ? How to start up the Edit menu ?Which items can be adjusted ? What can be done with the Edit File menu ?Read Amds Edit File OptionsConfirm Edit File Rename FileRandom Access Adjustment Mode How to change the characters ? Copy FileDelete File File SortFile Load Confirm Delete FilePicture Tuning What is CTI ?How to change the CTI setting ? CTI onWhat can be adjusted ? Available color temperatureAdjusting the Color Temperature Custom BalancePurpose What can be done ?How can it be selected ? To change the dynamic color depth valueTo change the noise reduction value Why adjusting the input balance ?How to adjust the input balance ? Noise ReductionTo start up the Geometry functions Which geometry adjustments are possible ?How can an adjustment be adjusted ? To start up the shift actionTo start up the size adjustment Aligning the keystoneAvailable Blanking Adjustment Adjusting the blankingBlanking Which Options are available within the Geometry menu ? Setting Up the Aspect RatioWhat can be done? Changing the Geometry OptionsInstallation Mode To view or to change the input configurationPossible results for the input slots Peripheral Configuration What if a switcher is connected to the projector ?What can be installed ? Defining the Output module of the RCVDS05Configuration Set up the Correct ConfigurationHow to change this color setting ? What will happenNo Signal Installation Mode Changing the Background ColorChanging the Shutdown Setting No SignalInternal Patterns How to select an internal pattern ?What can be done with these internal patterns ? LensHow to shift the image ? Installation Mode Zoom/Focus/Shift/TiltHow to Zoom/Focus ? How to tilt the image ?Quick Access Keys Installation Mode Bridge up or downHow to get an overview ? OptionsHow to set up? Service Mode Built-up of the service modeHow to display the Identification screen ? InformationDetailed description How to enable or disable the password function ? About password TypesAccess Control List Service Mode How to change the password ?Access Control List Access Control ListStart Up the Serial Communication menu How to change that address ?Entering the new projector address Serial CommunicationAvailable Baud rates Service Mode Setting up the Baud rateInstalling the Interface Standard RS422 TerminationHow to switch the constant light output ? Lamp information light output switchingHow to display the lamp menu How to add or the change the settings ?How to get add ins ? Service Mode Available settingsHow to start up ? Reset Input BalanceWhat can be seen ? Service Mode How to activate an add-in ?How to start the I2C diagnosis ? ADD-INSService Mode Confirm Quick Access Programmable Function Keys10-2 Barco ELM R12 Standard Source SET UP Files Appendix a Standard Source Set Up FilesSUNEWS67 Index IndexRCU