Barco R9001490 Getting Started Lamp Light Output Indication, Quick Language Change, Service

Page 45

Getting Started

Lamp Light Output Indication

When starting up and the center lumens measurement is lower than 50 % of its initial value, the lamp light output warning will be displayed for 1 minute. Press ENTER to continue. The message will not be repeated during operation.

WARNING

Lamp run time is 400 hours.

The light output of the lamp is less

than 50% of its initial value.

It is advisable to replace the lamp

before damage occurs.

<ENTER> to confirm

During operation and a start up without any message, the light output message will appear on the screen when the light output is reduced with 33% from its initial value.

This message will be repeated every hour.

Switching to Stand-by.

When the projector is running and you want to go to stand-by, press the stand-by key.

Switching Off

To switch off:

-First press STANDBY key and let the projector cool down until the fans stopblowing, or at least 15 min.

-Switch off the projector with the power switch.

Quick Set Up Adjustments

Quick Language Change

Only if different on screen languages are available, follow the next procedure to change the on screen language.

1Press ENTER to start up the adjustment mode.

2Press the cursor key  or  to highlight 'Service' (menu 1). When password protected, your password will be asked. (more explanation about access by password can be found in Chapter 'Start up the Adjustment mode'.

3Press ENTER to display the Service mode menu.

3Push the cursor key  or  to highlight 'Change Language' (menu 2). If not visible in the menu, highlight first 'More' and press ENTER to display a second service menu. Select then 'Change Language'.

4Press ENTER to display the language selection menu.

5Push the cursor key  or  to highlight the desired language (menu 3). For the moment, only English is available.

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS

INSTALLATION

SERVICE

Select with  or 

then <ENTER> <EXIT> to return.

menu1

SERVICE

IDENTIFICATION

CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS SERIAL COMMUNICATION LAMP

MORE..

Select with  or 

then <ENTER>

<EXIT> to return.

menu2

CHANGE LANGUAGE

English

Select with  or 

then <ENTER>

<EXIT> to return.

menu3

5-4		5976072 BARCOELM R12 17012000

Image 45

Contents Barco Projection Systems Barco n.v./Projection Systems Table of Contents Connections Start UP of the Adjustment Mode Installation Mode 10-1 Table of Contents To prevent battery explosion SafetyTo prevent personel injury To prevent projector damageSafety Packaging and Dimensions Front View DimensionsSide View Packaging and Dimensions Installation Guidelines Installation GuidelinesWhat image size? How big should the image be? Table/Top side facing ceiling Safety Area around the Projector Installing the projection lamp When transporting the projector Which Lens has to be selected Installing the Projection Lens 310a.DRW Stacking two Projectors Optional Profile Sections Switching on AC Power mains cord connectionConnections FusesSwitching Off Switching to Stand-byConnections Lamp Run Time Indication Lamp Runtime WarningInput facilities, RCVDS05 or VS05 connected Input facilitiesConnections Input module insertion into the projector How to change the input slot setting How to select input SlotConnections Fixed RGB analog input slot Range of interfaces made by BarcoFixed 5-Input Slot slot Which signals can be connected to slot 2 ?How to select What can be connected to the Video input ?What can be connected to the S-Video input ? Straps on module level Connections How to set the input priority ?What can be connected to these inputs ? How to select the RGB inputRemark Sync selection on the Input Slots menuRGB-SOG Indication on the input slot menu How to select the Component Video input16HSDRUP Floating Ordwlqjruqrqiordwlqjlqsxw How to select the RGB3S inputHow to select the Digital input What can be connected to this input ?Connections Connections How to select the Digital input Connecting an IR Remote Receiver to the projector Connections Connecting a VS05 to the projectorGetting Started Getting StartedRCU Getting Started TerminologyLamp Run Time Warning Getting Started Lamp Light Output Indication ServiceQuick Language Change Change LanguageLens Adjustment ZOOM/FOCUS Getting Started Quick Lens AdjustmentLens Adjustment Shift TiltPointing to the reflective screen Getting Started Quick On Screen Color changeOSD Color OSD Color Highlighted ItemHardwired to the XLR Input Getting Started Hardwired Remote InputSet up an Individual Projector Address Why a projector address ?How to control the projector or projectors ? Before using the RCUGetting Started Display the Projector Address on the Screen How to Program an Address into the RCU ?Input Selection Picture ContolsStand-by key Pause keyPasswordProtection Start up of the Adjustment ModeEntering the Password Start upMenus on Local LCD Display Setting Up the personalised PasswordsRandom Access Adjustment Mode Overview FlowchartStarting up Start up the File Service Connecting a new SourcePossible File Manipulations File AnnotationStart up the Load File How to load a file ?Image is not perfect ? Load FileWhich items can be adjusted ? How to start up the Edit menu ?How to change the settings ? What can be done with the Edit File menu ?Edit File Options Read AmdsRename File Confirm Edit FileCopy File Random Access Adjustment Mode How to change the characters ?File Load File SortDelete File Confirm Delete FileHow to change the CTI setting ? What is CTI ?Picture Tuning CTI onAdjusting the Color Temperature Available color temperatureWhat can be adjusted ? Custom BalanceHow can it be selected ? What can be done ?Purpose To change the dynamic color depth valueHow to adjust the input balance ? Why adjusting the input balance ?To change the noise reduction value Noise ReductionHow can an adjustment be adjusted ? Which geometry adjustments are possible ?To start up the Geometry functions To start up the shift actionAligning the keystone To start up the size adjustmentAvailable Blanking Adjustment Adjusting the blankingBlanking What can be done? Setting Up the Aspect RatioWhich Options are available within the Geometry menu ? Changing the Geometry OptionsInstallation Mode To view or to change the input configurationPossible results for the input slots What can be installed ? What if a switcher is connected to the projector ?Peripheral Configuration Defining the Output module of the RCVDS05How to change this color setting ? Set up the Correct ConfigurationConfiguration What will happenChanging the Shutdown Setting Installation Mode Changing the Background ColorNo Signal No SignalWhat can be done with these internal patterns ? How to select an internal pattern ?Internal Patterns LensHow to Zoom/Focus ? Installation Mode Zoom/Focus/Shift/TiltHow to shift the image ? How to tilt the image ?How to get an overview ? Installation Mode Bridge up or downQuick Access Keys OptionsHow to set up? Built-up of the service mode Service ModeHow to display the Identification screen ? InformationDetailed description About password Types How to enable or disable the password function ?Access Control List Service Mode How to change the password ?Access Control List Access Control ListEntering the new projector address How to change that address ?Start Up the Serial Communication menu Serial CommunicationInstalling the Interface Standard Service Mode Setting up the Baud rateAvailable Baud rates RS422 TerminationHow to display the lamp menu Lamp information light output switchingHow to switch the constant light output ? How to add or the change the settings ?How to start up ? Service Mode Available settingsHow to get add ins ? Reset Input BalanceHow to start the I2C diagnosis ? Service Mode How to activate an add-in ?What can be seen ? ADD-INSService Mode Programmable Function Keys Confirm Quick Access10-2 Barco ELM R12 Appendix a Standard Source Set Up Files Standard Source SET UP FilesSUNEWS67 Index IndexRCU