Barco R9001490 Connections Lamp Run Time Indication, Lamp Runtime Warning, Switching to Stand-by

Page 27

Connections

Lamp Run Time Indication

When starting up and the total run time of the lamp is 470 hours or more, the remaining lamp run time will be displayed for 1 minute. This warning message will be repeated every 30 minutes. Press EXIT to remove the message before the minute is over.

REMAINING LAMP RUN TIME 30 hours

When the total run time of the lamp is 500 hours or more, the following warning message, with the exact run time is displayed on the screen.

WARNING

Lamp run time is 500 hours Operating the lamp longer than 500 hours may damage the projector.

Please replace the lamp

<ENTER> to continue

Lamp run time is 500 hours. Operating the lamp longer than 500 hours may damage the projector. Please replace the lamp.

When OK (ENTER) is pressed to go on, the warning will be repeated every 30 min.

The total lifetime of the lamp for a safe operation is 500 hours max. Do not use it longer. Always replace with a same type of lamp. Call a BARCO authorized service technician for lamp replacement.

Lamp Runtime Warning

Using a lamp for more than 500 hours is dangerous as the lamp could explode.

Lamp Light Output Indication

When starting up and the center lumens measurement is lower than 50 % of its initial value, the lamp light output warning will be displayed for 1 minute. Press ENTER to continue. The message will not be repeated during operation.

WARNING

Lamp run time is 400 hours.

The light output of the lamp is less

than 50% of its initial value.

It is advisable to replace the lamp

before damage occurs.

<ENTER> to confirm

During operation and a start up without any message, the light output message will appear on the screen when the light output is reduced with 33% from its initial value.

This message will be repeated every hour.

Switching to Stand-by.

When the projector is running and you want to go to stand-by, press the stand-by key.

Switching Off

To switch off:

-First press STANDBY key and let the projector cool down until the fans stop blowing, or at least 15 min.

-Switch off the projector with the power switch.

4-2		5976072 BARCOELM R12 05052000

Image 27

Contents Barco Projection Systems Barco n.v./Projection Systems Table of Contents Connections Start UP of the Adjustment Mode Installation Mode 10-1 Table of Contents To prevent projector damage SafetyTo prevent battery explosion To prevent personel injurySafety Packaging and Dimensions Front View DimensionsSide View Packaging and Dimensions Installation Guidelines Installation GuidelinesWhat image size? How big should the image be? Table/Top side facing ceiling Safety Area around the Projector Installing the projection lamp When transporting the projector Which Lens has to be selected Installing the Projection Lens 310a.DRW Stacking two Projectors Optional Profile Sections Fuses AC Power mains cord connectionSwitching on ConnectionsLamp Runtime Warning Switching to Stand-bySwitching Off Connections Lamp Run Time IndicationInput facilities, RCVDS05 or VS05 connected Input facilitiesConnections Input module insertion into the projector Range of interfaces made by Barco How to select input SlotHow to change the input slot setting Connections Fixed RGB analog input slotFixed 5-Input Slot slot Which signals can be connected to slot 2 ?How to select What can be connected to the Video input ?What can be connected to the S-Video input ? Straps on module level Connections How to set the input priority ?Sync selection on the Input Slots menu How to select the RGB inputWhat can be connected to these inputs ? RemarkRGB-SOG Indication on the input slot menu How to select the Component Video input16HSDRUP Floating Ordwlqjruqrqiordwlqjlqsxw How to select the RGB3S inputHow to select the Digital input What can be connected to this input ?Connections Connections How to select the Digital input Connecting an IR Remote Receiver to the projector Connections Connecting a VS05 to the projectorGetting Started Getting StartedRCU Getting Started TerminologyLamp Run Time Warning Change Language ServiceGetting Started Lamp Light Output Indication Quick Language ChangeTilt Getting Started Quick Lens AdjustmentLens Adjustment ZOOM/FOCUS Lens Adjustment ShiftOSD Color Highlighted Item Getting Started Quick On Screen Color changePointing to the reflective screen OSD ColorHardwired to the XLR Input Getting Started Hardwired Remote InputBefore using the RCU Why a projector address ?Set up an Individual Projector Address How to control the projector or projectors ?Picture Contols How to Program an Address into the RCU ?Getting Started Display the Projector Address on the Screen Input SelectionStand-by key Pause keyStart up Start up of the Adjustment ModePasswordProtection Entering the PasswordMenus on Local LCD Display Setting Up the personalised PasswordsRandom Access Adjustment Mode Overview FlowchartStarting up File Annotation Connecting a new SourceStart up the File Service Possible File ManipulationsLoad File How to load a file ?Start up the Load File Image is not perfect ?What can be done with the Edit File menu ? How to start up the Edit menu ?Which items can be adjusted ? How to change the settings ?Edit File Options Read AmdsRename File Confirm Edit FileCopy File Random Access Adjustment Mode How to change the characters ?Confirm Delete File File SortFile Load Delete FileCTI on What is CTI ?How to change the CTI setting ? Picture TuningCustom Balance Available color temperatureAdjusting the Color Temperature What can be adjusted ?To change the dynamic color depth value What can be done ?How can it be selected ? PurposeNoise Reduction Why adjusting the input balance ?How to adjust the input balance ? To change the noise reduction valueTo start up the shift action Which geometry adjustments are possible ?How can an adjustment be adjusted ? To start up the Geometry functionsAligning the keystone To start up the size adjustmentAvailable Blanking Adjustment Adjusting the blankingBlanking Changing the Geometry Options Setting Up the Aspect RatioWhat can be done? Which Options are available within the Geometry menu ?Installation Mode To view or to change the input configurationPossible results for the input slots Defining the Output module of the RCVDS05 What if a switcher is connected to the projector ?What can be installed ? Peripheral ConfigurationWhat will happen Set up the Correct ConfigurationHow to change this color setting ? ConfigurationNo Signal Installation Mode Changing the Background ColorChanging the Shutdown Setting No SignalLens How to select an internal pattern ?What can be done with these internal patterns ? Internal PatternsHow to tilt the image ? Installation Mode Zoom/Focus/Shift/TiltHow to Zoom/Focus ? How to shift the image ?Options Installation Mode Bridge up or downHow to get an overview ? Quick Access KeysHow to set up? Built-up of the service mode Service ModeHow to display the Identification screen ? InformationDetailed description About password Types How to enable or disable the password function ?Access Control List Service Mode How to change the password ?Access Control List Access Control ListSerial Communication How to change that address ?Entering the new projector address Start Up the Serial Communication menuRS422 Termination Service Mode Setting up the Baud rateInstalling the Interface Standard Available Baud ratesHow to add or the change the settings ? Lamp information light output switchingHow to display the lamp menu How to switch the constant light output ?Reset Input Balance Service Mode Available settingsHow to start up ? How to get add ins ?ADD-INS Service Mode How to activate an add-in ?How to start the I2C diagnosis ? What can be seen ?Service Mode Programmable Function Keys Confirm Quick Access10-2 Barco ELM R12 Appendix a Standard Source Set Up Files Standard Source SET UP FilesSUNEWS67 Index IndexRCU