Barco R9001490 owner manual Confirm Edit File, Rename File

Page 59

Random Access Adjustment Mode

Field Polarity :

The field polarity function is used for interlaced images. Both rasters of the image could be shifted in a wrong way (double lines are visilble in the image). This can be corrected by forcing the field polarity to [neg] or [pos].

Use the ENTER key to toggle between [pos] and [neg].

Field Select : Default [both]

The field select is only used for interlaced images. One frame of an interlaced image contains two fields, an even and an odd field. The choice exists to project [both] fields on the screen or only the [even] or [odd] field. This can be useful for 3D projection. Use the ENTER key to toggle between [both], [even] and [odd].

Vertical Refresh [sync/async] : The way of updating the image information on the LCD panels.

Not available for PAL-SECAM-NTSC sources. This option will b displayed in gray.

1For sources with a vertical frequency up to 60 Hz : the vertical refresh rate is the same as the vertical frequency of the incoming source. This is a necessity to project moving images without 'motion artifacts'. For stationary images with a vertical frequency up to 60 Hz it is still possible to use asynchronous refresh. When loading Pal, Secam, NTSC-files the synchronous mode is default, for all other sources below 60 Hz asynchronous mode is default.

2For sources with a vertical frequency higher that 60 Hz : the vertical refresh is different than the vertical frequency of the incoming source. Synchronous refresh cannot be used.

Vertical Sync Polarity : [leading] or [trailing]

The vertical refresh can be synchronised with the leading sync edge or trailing sync edge. Default on [leading].

Toggling to [trailing] is only necessary for special applications where the trailing edge of the sync signal has to be taken as a reference. Use the ENTER key to toggle between [leading] or [trailing]

Press EXIT to leave the Edit File Option menu.

A 'Confirm Edit File' menu will be displayed.

CONFIRM

EDIT FILE

Save changes to file

xga.c30?

<ENTER> to confirm

<EXIT> to return

Press ENTER to confirm and to save the new settings or EXIT to return without saving the new entered settings.

Rename a file

Start Up.

To change the name of a selected file:

1Push the cursor key or to highlight 'Rename' (menu 1).

2 Press ENTER.

The Rename selection menu will be displayed (menu 2).

3 Push the cursor key or to select a file name (menu 2). 4 Press ENTER to select.

The Rename menu will be displayed with the selected file name already filled in, in the 'From file name :' area and in the 'To file name :' area.

The first character in the 'To file name :' area is highlighted (menu 3).

FILE SERVICE

LOAD

EDIT

RENAME

COPY

DELETE

OPTIONS

Select with or

then <ENTER> <EXIT> to return.

menu1

RENAME FILE

Filename Src Resolution

-----------------------------------------------------

Video525.s01 1

675x240i

Video525.c01

1

675x240i

Video525.c02

1

675x240i

-----------------------------------------------------

Active file : Video525.c50

Select with or

then <ENTER>

<EXIT> to return.

menu2

RENAME FILE

Frome file name :

Video525.s01 To file name : demo.c10

Select with or

Reprogram with or

or numeric keys

<ENTER> to confirm

<EXIT> to return

menu3

7-6

 

5976072 BARCOELM R12 17012000

 

Page 58 Page 60
Image 59
Page 58 Page 60
Contents Barco Projection Systems Barco n.v./Projection Systems Table of Contents Connections Start UP of the Adjustment Mode Installation Mode 10-1 Table of Contents To prevent projector damage SafetyTo prevent battery explosion To prevent personel injurySafety Packaging and Dimensions Front View DimensionsSide View Packaging and Dimensions Installation Guidelines Installation GuidelinesWhat image size? How big should the image be? Table/Top side facing ceiling Safety Area around the Projector Installing the projection lamp When transporting the projector Which Lens has to be selected Installing the Projection Lens 310a.DRW Stacking two Projectors Optional Profile Sections Fuses AC Power mains cord connectionSwitching on ConnectionsLamp Runtime Warning Switching to Stand-bySwitching Off Connections Lamp Run Time IndicationInput facilities, RCVDS05 or VS05 connected Input facilitiesConnections Input module insertion into the projector Range of interfaces made by Barco How to select input SlotHow to change the input slot setting Connections Fixed RGB analog input slotFixed 5-Input Slot slot Which signals can be connected to slot 2 ?What can be connected to the S-Video input ? How to selectWhat can be connected to the Video input ? Straps on module level Connections How to set the input priority ?Sync selection on the Input Slots menu How to select the RGB inputWhat can be connected to these inputs ? RemarkRGB-SOG Indication on the input slot menu How to select the Component Video input16HSDRUP Floating Ordwlqjruqrqiordwlqjlqsxw How to select the RGB3S inputConnections How to select the Digital inputWhat can be connected to this input ? Connections How to select the Digital input Connecting an IR Remote Receiver to the projector Connections Connecting a VS05 to the projectorGetting Started Getting StartedRCU Getting Started TerminologyLamp Run Time Warning Change Language ServiceGetting Started Lamp Light Output Indication Quick Language ChangeTilt Getting Started Quick Lens AdjustmentLens Adjustment ZOOM/FOCUS Lens Adjustment ShiftOSD Color Highlighted Item Getting Started Quick On Screen Color changePointing to the reflective screen OSD ColorHardwired to the XLR Input Getting Started Hardwired Remote InputBefore using the RCU Why a projector address ?Set up an Individual Projector Address How to control the projector or projectors ?Picture Contols How to Program an Address into the RCU ?Getting Started Display the Projector Address on the Screen Input SelectionStand-by key Pause keyStart up Start up of the Adjustment ModePasswordProtection Entering the PasswordMenus on Local LCD Display Setting Up the personalised PasswordsStarting up Random Access Adjustment ModeOverview Flowchart File Annotation Connecting a new SourceStart up the File Service Possible File Manipulations Load File How to load a file ? Start up the Load File Image is not perfect ?What can be done with the Edit File menu ? How to start up the Edit menu ?Which items can be adjusted ? How to change the settings ?Edit File Options Read AmdsRename File Confirm Edit FileCopy File Random Access Adjustment Mode How to change the characters ?Confirm Delete File File SortFile Load Delete FileCTI on What is CTI ?How to change the CTI setting ? Picture TuningCustom Balance Available color temperatureAdjusting the Color Temperature What can be adjusted ?To change the dynamic color depth value What can be done ?How can it be selected ? PurposeNoise Reduction Why adjusting the input balance ?How to adjust the input balance ? To change the noise reduction valueTo start up the shift action Which geometry adjustments are possible ?How can an adjustment be adjusted ? To start up the Geometry functionsAligning the keystone To start up the size adjustmentBlanking Available Blanking AdjustmentAdjusting the blanking Changing the Geometry Options Setting Up the Aspect RatioWhat can be done? Which Options are available within the Geometry menu ?Possible results for the input slots Installation ModeTo view or to change the input configuration Defining the Output module of the RCVDS05 What if a switcher is connected to the projector ?What can be installed ? Peripheral ConfigurationWhat will happen Set up the Correct ConfigurationHow to change this color setting ? ConfigurationNo Signal Installation Mode Changing the Background ColorChanging the Shutdown Setting No SignalLens How to select an internal pattern ?What can be done with these internal patterns ? Internal PatternsHow to tilt the image ? Installation Mode Zoom/Focus/Shift/TiltHow to Zoom/Focus ? How to shift the image ?Options Installation Mode Bridge up or downHow to get an overview ? Quick Access KeysHow to set up? Built-up of the service mode Service ModeDetailed description How to display the Identification screen ?Information About password Types How to enable or disable the password function ?Access Control List Service Mode How to change the password ?Access Control List Access Control ListSerial Communication How to change that address ?Entering the new projector address Start Up the Serial Communication menuRS422 Termination Service Mode Setting up the Baud rateInstalling the Interface Standard Available Baud ratesHow to add or the change the settings ? Lamp information light output switchingHow to display the lamp menu How to switch the constant light output ?Reset Input Balance Service Mode Available settingsHow to start up ? How to get add ins ?ADD-INS Service Mode How to activate an add-in ?How to start the I2C diagnosis ? What can be seen ?Service Mode Programmable Function Keys Confirm Quick Access10-2 Barco ELM R12 Appendix a Standard Source Set Up Files Standard Source SET UP FilesSUNEWS67 Index IndexRCU
Top Page Image Contents