Barco R9001490 owner manual Getting Started Terminology, Rcu

Page 43

Getting Started

Terminology

1Barco key : = selection key, to get direct access to the lens adjustment menus.

2ADJ. : ADJUST key, to enter or exit the adjustment mode.

3Address key (recessed key), to enter the address of the projector (between 0 and 9). Press the recessed address key with a pencil, followed by pressing one digit button between 0 and 9.

4STBY : stand-by button, to start projector when the power switch is switched on and to switch off the projector without switching off the power switch.

5PAUSE : to stop projection for a short time, press 'PAUSE'. The image disappears but full power is retained for immediate restarting.

6Help : on line help information (not yet available)

7Digit buttons : direct input selection.

8Picture controls : use these buttons to obtain the desired picture analog level.

9PHASE : used to remove the instability of the image.

10TEXT : when adjusting one of the image, e.g. controls during a meeting, the displayed bar scale can be removed by pressing 'TEXT' key first. To re-display the bar scale on the screen, press 'TEXT' key again.

When TEXT is 'off', no adjustment menu's will be displayed on the screen when entering the adjustment mode.

11FREEZ : press to freeze the projected image.

12ENTER : to start up the adjustment mode or to confirm an adjustment or selection in the adjustment mode.

13EXIT : to leave the adjustment mode or to scroll upwards when in the adjustment mode.

14Cursor Keys (on RCU) or '+' and '-' keys (cursor keys) on the local keypad : to make menu selections when in the adjustment mode or to zoom/focus when the direct access is active.

Comparision between the cursor keys and the use of the '+' and '-' keys on the local keypad :

RCU

 

 

 

=

local keypad

cursor key up

=

'+' key up

 

cursor

key down

=

'-' key down

cursor key

right

=

'+' key right

cursor

key

left

=

'-' key left

 

Use the '+' and '-' keys (cursor keys) : to increase or decrease the analog level of the image controls when they are first selected.

15RC operating indication : lights up when a button on the remote control is pressed. (This is a visual indicator to check the operation of the remote control)

5-2

 

5976072 BARCOELM R12 17012000

 

Image 43
Contents Barco Projection Systems Barco n.v./Projection Systems Table of Contents Connections Start UP of the Adjustment Mode Installation Mode 10-1 Table of Contents To prevent projector damage SafetyTo prevent battery explosion To prevent personel injurySafety Packaging and Dimensions Front View DimensionsSide View Packaging and Dimensions Installation Guidelines Installation GuidelinesWhat image size? How big should the image be? Table/Top side facing ceiling Safety Area around the Projector Installing the projection lamp When transporting the projector Which Lens has to be selected Installing the Projection Lens 310a.DRW Stacking two Projectors Optional Profile Sections Fuses AC Power mains cord connectionSwitching on ConnectionsLamp Runtime Warning Switching to Stand-bySwitching Off Connections Lamp Run Time IndicationInput facilities, RCVDS05 or VS05 connected Input facilitiesConnections Input module insertion into the projector Range of interfaces made by Barco How to select input SlotHow to change the input slot setting Connections Fixed RGB analog input slotFixed 5-Input Slot slot Which signals can be connected to slot 2 ?What can be connected to the Video input ? How to selectWhat can be connected to the S-Video input ? Straps on module level Connections How to set the input priority ?Sync selection on the Input Slots menu How to select the RGB inputWhat can be connected to these inputs ? RemarkRGB-SOG Indication on the input slot menu How to select the Component Video input16HSDRUP Floating Ordwlqjruqrqiordwlqjlqsxw How to select the RGB3S inputWhat can be connected to this input ? How to select the Digital inputConnections Connections How to select the Digital input Connecting an IR Remote Receiver to the projector Connections Connecting a VS05 to the projectorGetting Started Getting StartedRCU Getting Started TerminologyLamp Run Time Warning Change Language ServiceGetting Started Lamp Light Output Indication Quick Language ChangeTilt Getting Started Quick Lens AdjustmentLens Adjustment ZOOM/FOCUS Lens Adjustment ShiftOSD Color Highlighted Item Getting Started Quick On Screen Color changePointing to the reflective screen OSD ColorHardwired to the XLR Input Getting Started Hardwired Remote InputBefore using the RCU Why a projector address ?Set up an Individual Projector Address How to control the projector or projectors ?Picture Contols How to Program an Address into the RCU ?Getting Started Display the Projector Address on the Screen Input SelectionStand-by key Pause keyStart up Start up of the Adjustment ModePasswordProtection Entering the PasswordMenus on Local LCD Display Setting Up the personalised PasswordsOverview Flowchart Random Access Adjustment ModeStarting up File Annotation Connecting a new SourceStart up the File Service Possible File ManipulationsLoad File How to load a file ?Start up the Load File Image is not perfect ?What can be done with the Edit File menu ? How to start up the Edit menu ?Which items can be adjusted ? How to change the settings ?Edit File Options Read AmdsRename File Confirm Edit FileCopy File Random Access Adjustment Mode How to change the characters ?Confirm Delete File File SortFile Load Delete FileCTI on What is CTI ?How to change the CTI setting ? Picture TuningCustom Balance Available color temperatureAdjusting the Color Temperature What can be adjusted ?To change the dynamic color depth value What can be done ?How can it be selected ? PurposeNoise Reduction Why adjusting the input balance ?How to adjust the input balance ? To change the noise reduction valueTo start up the shift action Which geometry adjustments are possible ?How can an adjustment be adjusted ? To start up the Geometry functionsAligning the keystone To start up the size adjustmentAdjusting the blanking Available Blanking AdjustmentBlanking Changing the Geometry Options Setting Up the Aspect RatioWhat can be done? Which Options are available within the Geometry menu ?To view or to change the input configuration Installation ModePossible results for the input slots Defining the Output module of the RCVDS05 What if a switcher is connected to the projector ?What can be installed ? Peripheral ConfigurationWhat will happen Set up the Correct ConfigurationHow to change this color setting ? ConfigurationNo Signal Installation Mode Changing the Background ColorChanging the Shutdown Setting No SignalLens How to select an internal pattern ?What can be done with these internal patterns ? Internal PatternsHow to tilt the image ? Installation Mode Zoom/Focus/Shift/TiltHow to Zoom/Focus ? How to shift the image ?Options Installation Mode Bridge up or downHow to get an overview ? Quick Access KeysHow to set up? Built-up of the service mode Service ModeInformation How to display the Identification screen ?Detailed description About password Types How to enable or disable the password function ?Access Control List Service Mode How to change the password ?Access Control List Access Control ListSerial Communication How to change that address ?Entering the new projector address Start Up the Serial Communication menuRS422 Termination Service Mode Setting up the Baud rateInstalling the Interface Standard Available Baud ratesHow to add or the change the settings ? Lamp information light output switchingHow to display the lamp menu How to switch the constant light output ?Reset Input Balance Service Mode Available settingsHow to start up ? How to get add ins ?ADD-INS Service Mode How to activate an add-in ?How to start the I2C diagnosis ? What can be seen ?Service Mode Programmable Function Keys Confirm Quick Access10-2 Barco ELM R12 Appendix a Standard Source Set Up Files Standard Source SET UP FilesSUNEWS67 Index IndexRCU