Rackmount Solutions PRO500E Turning The Unit On/Off, English, ON / OFF / Test Button, Self Test

Page 10
TURNING THE UNIT ON/OFF

English

TURNING THE UNIT ON/OFF

ON / OFF / Test Button

Press and release the ON/OFF/Test Button after one beep to turn the UPS ON and supply power to the load. The load is immediately powered while the UPS runs a two-second self test. Press and release the ON/OFF/Test Button after one beep to turn the UPS OFF. The UPS will continue to charge the batteries whenever it is plugged into an AC outlet and there is AC present.

SELF TEST

The self test feature is useful to verify the correct operation of the UPS and the condition of the batteries. With the UPS in the normal On-Line mode, press and hold the ON/OFF/Test Button for approximately 4 seconds (four beeps), then release the button. The UPS will perform a ten-second self test. During the self test, the UPS will switch to battery power and the On-Line LED will blink and the audible alarm will sound. The length of the test that is automati- cally performed every two weeks is longer than the start-up or user invoked test. This test will run for approximately fifteen-seconds to measure the battery’s capability to provide an acceptable amount of runtime. If the UPS fails a self test, one of the LEDs will remain illuminated indicating the type of problem.

Note: The UPS will automatically perform a self test on start-up and every two weeks.

DIP SWITCH SETTINGS

The DIP Switch setting may be changed by the user to set the desired Inverter (on battery) output voltage. The DIP Switch must be set to the desired Inverter output voltage and then the UPS must be turned OFF and restarted to reconfigure the microprocessor and save the changes. The Inverter (on battery) output voltage setting for the 120V models can be either 120VAC (default) or 127VAC. Changing the Inverter output voltage to 127VAC, will also change the Buck setpoint from 130VAC (default) to 136VAC. The Inverter (on battery) output voltage setting for the 230V models can be either 230VAC (default) or 208VAC. Changing the Inverter output voltage to 208VAC, will also change the Boost1 setpoint from 206VAC (default) to 198VAC.

Inverter output voltage

Switch 1 2 120V (230V)

127V (208V)

9

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Page PRO-E Series Users Manual This symbol indicates Risk of Electrical Shock IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONSThis symbol indicates ATTENTION This symbol indicates Direct Current SupplyAUTHORIZED SERVICE PERSONNEL ONLY Receiving Inspection Para Systems Life Support PolicyOn-Line/On-Battery/Boost/Buck LED Fault LED Overload LED WARNING The 230V models are NETWORK PROTECTION ONLY REAR PANEL120V Models 230V ModelsINSTALLATION INSTALLATION PLACEMENTCONNECTING YOUR EQUIPMENT CHARGING THE BATTERY CONNECTING THE UPS TO AN AC SOURCECHECKING THE SITE WIRING FAULT COMMUNICATIONS PORT CONNECTION OPTIONALON / OFF / Test Button DIP SWITCH SETTINGSTURNING THE UNIT ON/OFF SELF TESTWEAK/BAD BATTERY ALARMS ON BATTERYLOW BATTERY WARNING UPS FAULTCOMMUNICATIONS PORTS RS232 and USB Press and release the On/Off Check the specifications seeEnglish even though there isREPLACING THE BATTERY BATTERY REPLACEMENT PROCEDURE Yuasa9. Disconnect the positive red wire from the battery positve terminal IF THE UPS REQUIRES SERVICE PRO700E MODEL NUMBERPRO500E PRO1100EFunction DefaultThese items may require optional software or hardware FactoryPara Systems Inc. Para Systems warrants this equipment, when properly applied and operated within specified conditions, against faulty materials or workmanship for a period of three years from the date of purchase. For equip- ment sites within the United States and Canada, this warranty covers repair or replacement of defective equipment at the discretion of Para Systems. Repair will be from the nearest authorized service center. Replacement parts and warranty labor will be borne by Para Systems. For equipment located outside of the United States and Canada, Para Systems only covers faulty parts. Para Systems products repaired or replaced pursuant to this warranty shall be war- ranted for the unexpired portion of the warranty applying to the original product. This warranty applies only to the original purchaser who must have properly registered the product within 10 days of purchase LIMITED PRODUCT WARRANTY ContinuedRobert Calhoun DECLARATION OF CONFORMITYEnglish
Top Page Image Contents