Onkyo Complete Guide for Network Settings and Firmware Updates for Your Receiver
Page 62

Network

After modifying the network settings, you must confirm the changes by executing “Save”.

This section explains how to configure the AV receiver’s network settings manually.

If your router’s DHCP server is enabled, you don’t need to change any of these settings, as the AV receiver is set to use DHCP to configure itself automatically by default (i.e., DHCP is set to “Enable”). If, however, your router’s DHCP server is disabled (you’re for example using static IP), you’ll need to configure these settings yourself, in which case, a knowledge of Ethernet networking is essential.

What’s DHCP?

DHCP (Dynamic Host Configuration Protocol) is used by routers, computers, the AV receiver, and other devices to automatically configure themselves on a network.

What’s DNS?

The DNS (Domain Name System) translates domain names into IP addresses. For example, when you enter a domain name such as www.onkyousa.com in your Web browser, before accessing the site, your browser uses DNS to translate this into an IP address, in this case 63.148.251.142.

■MAC Address

This is the AV receiver’s MAC (Media Access Control) address. This address cannot be changed.

■DHCP

`Enable

`Disable

This setting determines whether or not the AV receiver uses DHCP to automatically configure its IP Address, Subnet Mask, Gateway, and DNS Server settings.

Note

•If you select “Disable”, you must configure the “IP Address”, “Subnet Mask”, “Gateway”, and “DNS Server” settings yourself.

■IP Address

`Class A:

“10.0.0.0” to “10.255.255.255”

`Class B:

“172.16.0.0” to “172.31.255.255”

`Class C:

“192.168.0.0” to “192.168.255.255” Enter a static IP address provided by your ISP. Most routers use Class C IP addresses.

■Subnet Mask

Enter the subnet mask address provided by your ISP (typically 255.255.255.0).

■Gateway

Enter the gateway address provided by your ISP.

■DNS Server

Enter the DNS server address provided by your ISP.

En

■Proxy URL

To use a Web proxy, enter its URL here.

■Proxy Port

If you’re using a Web proxy, enter a proxy port number here.

■Network Control

`Enable

`Disable

This setting enables or disables control over the network.

Note

•When set to “Enable”, the NET indicator is dimly-lit and the power consumption slightly increases in standby mode.

■Control Port

`“49152” to “65535”

This is the network port used for control over the network.

Note

•When the “Network Control” setting is set to “Disable”, this setting is cannot be selected.

Firmware Update

See “Firmware Update” for the update procedure

(➔ page 85).

Note

•Perform the firmware update only when such an announcement is posted on the Onkyo web site. Visit the Onkyo web site for the latest information.

•It takes maximum 60 minutes to complete the firmware update.

•When updating a firmware from a USB mass storage device, the AV receiver searches the device which is connected earlier during power on. If two devices have been connected at the time of power on, the AV receiver will search the device on the front panel.

■Version

Displays the current version of the firmware.

■Receiver

`via NET:

Performs the firmware update via Internet. Check the network connection before updating.

`via USB:

Performs the firmware update from a USB device. These settings allow you to update the AV receiver’s firmware. Do not shutdown the power of the AV receiver while updating.

■Universal Port

`via NET:

Performs the firmware update via Internet. Check the network connection before updating.

`via USB:

Performs the firmware update from a USB device. These settings allow you to update Onkyo dock’s firmware. Do not shutdown the power of the AV receiver while updating.

Note

•This update shall not be performed when no dock is connected to the UNIVERSAL PORT jack.

62

Page 61 Page 63
Image 62
Page 61 Page 63
Contents TX-NR809 Board above the apparatus shall be set 10 cm Local regulations when disposing of batteries10 cm 4 at the rear. The rear edge of the shelf or Away from the rear panel or wall, creating a flue-likePrecautions Aiming the remote controller Supplied AccessoriesInstalling the batteries TransmissionContents Amplifier FeaturesServices available may vary depending on the region ProcessingTHX Select2 Plus North American and Taiwan models Front & Rear PanelsFront Panel European, Australian and Asian modelsDisplay Zone 2 and Zone 3 PRE/LINE OUT jacks Rear PanelFront L/R, CENTER, Surr L/R, SB/FH/FW Subwoofer Front L/R, CENTER, Surr L/RDimmer button Display button Muting button Remote ControllerControlling the AV Receiver Controlling the tunerConnecting the Speaker Cables Connecting the AV ReceiverConnecting Your Speakers Screw-type speaker terminalsAttaching the Speaker Cable Labels Speaker ConfigurationSpeaker Connection Precautions Number SpeakersBi-amping the Front Speakers Using Dipole SpeakersUsing a Powered Subwoofer TipConnecting a Power Amplifier AV Cables and Jacks Connecting AV componentsAbout AV Connections Hdmi cableJack Components Assignable Connecting Components with HdmiAudio Return Channel ARC function Audio Return Channel is set to AutoConnecting Your Components EFGHow to record a video source Jack/Port Components AssignableSystem On/Auto Power On Connecting Onkyo uComponentsConnecting a Recording Component Remote ControlPlug the power cord into an AC wall outlet Connecting the AntennasConnecting the Power Cord North AmericanTurning On AV receiver enters standby modeTurning On/Off the AV Receiver Turning OffPlayback Selecting the Language for the Onscreen Setup MenusControlling Contents of USB or Network Devices Playing the Connected ComponentEnter Understanding Icons on the DisplayPlaying an iPod/iPhone via USB Playing a USB Device Listening to Internet RadioTop menu of Internet Radio Listening to Other Internet RadioRegistering My Favorites*1 Playing Music Files on a Server Windows Media Player 11 SetupWindows Media Player 12 Setup Remote PlaybackTuning into Radio Stations Using Remote PlaybackUsing the Tuner Listening to AM/FM RadioMode Presetting AM/FM StationsUsing RDS excluding North American and Taiwan models Listening to Traffic News TP Displaying Radio Text RTFinding Stations by Type PTY Measurement procedure Using Basic FunctionsUsing the Automatic Speaker Setup First measurement positionUse q/wto select a target, and use e/rto change the setting When you’ve finished making the settings, press` Cancel Press Enter Disconnect the speaker setup microphoneError Messages Changing the Speaker Setup ManuallyUsing the Listening Modes Selecting Listening ModesExplanatory Notes Following audio formats are supported by the listening modeAbout Listening Modes Input SourceOnkyo-Original DSP Listening Modes Listening ModesDTS DSD*6Audyssey DSX *8 THXListening Mode Description Input Speaker Source Layout Setting the Display Brightness Using the Home MenuUsing the Sleep Timer Changing the Input Display Using the Whole House ModeDisplaying Source Information VCR/DVRMuting the AV Receiver Using HeadphonesSelecting Speaker Layout Press Receiver followed by SP Layout repeatedly to selectUsing Easy Macros RecordingCommon Procedures in Setup Menu Advanced SetupOn-screen Setup Menus Explanatory NotesInput/Output Assign Monitor OutBD/DVD, VCR/DVR, CBL/SAT, GAME, PC TV/CD, PHONO, Port Hdmi InputComponent Video Input BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX TV/CD, PHONO, PortDigital Audio Input Speaker SetupSpeaker Settings Analog Audio InputCenter*1, Surround*1, Surround Back*2*3*4 Subwoofer PhaseFront Front Wide*1*2*4, Front High*1*2*4Level Calibration Wireless SubwooferSpeaker Distance UnitBGC Equalizer SettingsTHX Audio Setup Dolby Audio AdjustMultiplex/Mono LFE Level Theater-DimensionalAudyssey DSX Source Setup AudysseyName Edit IntelliVolumeSync Wide Mode*1*2 Picture AdjustTo correct a character Picture Mode*1Film Mode*3*5*6 Resolution*3*5Game Mode*3*4*5 Edge Enhancement*3*5*6Audio Selector Listening Mode Preset Charge ModeOSD Setup Hardware SetupVolume Setup MiscellaneousMulti Zone TunerAudio Return Channel Auto StandbyAudio TV Out Lip SyncDhcp Firmware UpdateNetwork Using the Audio Settings Remote Controller SetupLock Setup Late Night Dolby VolumeSpeaker Levels Music Optimizer Music OptimizerRe-EQ Re-EQMulti Zone Connecting Your Zone 2 Speakers Directly to the AV receiverConnecting the Zone Speakers to an Additional Amplifier Making Multi Zone Connections8RECEIVER Operating on the remote controllerControlling Zone 2/3 Components Muting Zones Adjusting the Volume for ZonesAdjusting the Tone and Balance of Zone Using a Multiroom Kit with Other Components Using a Multiroom Kit with ZoneUsing a Multiroom Kit with a Cabinet UP-A1 Dock Using the Onkyo DockIPod/iPhone Playback via Onkyo Dock Controlling Your iPod/iPhone RI DockAvailable buttons RandomUse q/wto select a category, and then press Looking up for Remote Control CodePress Receiver followed by Setup Use q/w/e/rto select a character, and then pressEntering Remote Control Codes Resetting the Remote Controller Remote Control Codes for Onkyo Components Connected via uResetting Remote Mode Buttons Controlling Other Components8SOURCE*1 Input Enter Setup Search Repeat Random ModeVCR/PVR Guide TOP MenuFollowing buttons cannot learn new commands Learning CommandsDeleting Acquired Commands RemoteRunning Macros Using Normal MacrosMaking Macros Deleting MacrosAudio TroubleshootingPower Speaker volume cannot be set as required There’s no sound with a certain signal formatCan’t select the Pure Audio listening mode About DTS signalsTuner Remote ControllerVideo Zone 2/3 UP-A1 Dock for iPod/iPhoneRecording Music Server and Internet RadioUSB Device Playback OthersImportant Note Regarding Video Playback Component Video Monitor OUTUpdating the Firmware via Network Firmware UpdateUpdate procedure Before you startUpdating the Firmware via USB TroubleshootingErrors during an update via network Errors during an update via USB Press Receiver followed by Setup on Remote controllerUsing 8ON/STANDBY on the front panel, turn Select via USB and press EnterConnection Tips and Video Signal Path Video Connection FormatsAudio Connection Formats OUTOutput Video Resolution ChartOutput Input 4K *2 1080p/24 1080i 720p 480p/576p 480i/576iOperations that can be performed with Connection Using an RIHD-compatible TV, Player, or RecorderAbout p-compatible components Confirm the settings How to connect and setupConfirm the connecting and setting Operate with the remote controllerAbout Copyright Protection About HdmiSupported Audio Formats Network Requirements Network/USB FeaturesConnecting to the Network Server playback Server RequirementsUSB Device Requirements Remote playbackSupported Audio File Formats About DlnaVideo Section SpecificationsAmplifier Section Tuner Section GeneralAudio Outputs OthersMemo 4 0 0 7 0
Top Page Image Contents