Onkyo TX-NR809 Important Note Regarding Video Playback, Component Video Monitor OUT

Page 84

If the picture on your TV/monitor connected to the HDMI output(s) is unstable, try switching the DeepColor function off

To turn off the DeepColor function, simultaneously press the CBL/SAT and 8ON/STANDBY buttons on the AV receiver. While holding down CBL/SAT, press 8ON/STANDBY until “Off” appears on the display. Then, release both buttons. To reactivate the DeepColor function, repeat the above process until “On” appears on the display and release the buttons.

The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in.

Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s malfunction. Before you record important data, make sure that the material will be recorded correctly.

Before disconnecting the power cord from the wall outlet, set the AV receiver to standby.

Important Note Regarding Video Playback

The AV receiver can upconvert component video, S- Video, and composite video sources for display on a TV connected to the HDMI output(s). However, if the picture quality of the source is poor, upconversion may make the picture worse or disappear altogether.

In this case, try the following:

1 If the video source is connected to a component video input, connect your TV to the

COMPONENT VIDEO MONITOR OUT.

If the video source is connected to an S-Video input, connect your TV to a MONITOR OUT S.

If the video source is connected to a composite video input, connect your TV to the MONITOR OUT V.

2 On the main menu, select “Input/Output Assign” and then “Component Video Input” (page 46).

If the video source is connected to COMPONENT VIDEO IN 1, select the relevant input selector, and assign it to “IN1”.

If the video source is connected to COMPONENT VIDEO IN 2, select the relevant input selector, and assign it to “IN2”.

If the video source is connected to an S-Video input or composite video input, select the relevant input selector, and assign it to “- - - - -”.

En

84

Image 84
Contents TX-NR809 Local regulations when disposing of batteries 10 cm 4 at the rear. The rear edge of the shelf orBoard above the apparatus shall be set 10 cm Away from the rear panel or wall, creating a flue-likePrecautions Supplied Accessories Installing the batteriesAiming the remote controller TransmissionContents Features Services available may vary depending on the regionAmplifier ProcessingTHX Select2 Plus Front & Rear Panels Front PanelNorth American and Taiwan models European, Australian and Asian modelsDisplay Rear Panel Front L/R, CENTER, Surr L/R, SB/FH/FW SubwooferZone 2 and Zone 3 PRE/LINE OUT jacks Front L/R, CENTER, Surr L/RRemote Controller Controlling the AV ReceiverDimmer button Display button Muting button Controlling the tunerConnecting the AV Receiver Connecting Your SpeakersConnecting the Speaker Cables Screw-type speaker terminalsSpeaker Configuration Speaker Connection PrecautionsAttaching the Speaker Cable Labels Number SpeakersUsing Dipole Speakers Using a Powered SubwooferBi-amping the Front Speakers TipConnecting a Power Amplifier Connecting AV components About AV ConnectionsAV Cables and Jacks Hdmi cableConnecting Components with Hdmi Audio Return Channel ARC functionJack Components Assignable Audio Return Channel is set to AutoConnecting Your Components EFGHow to record a video source Jack/Port Components AssignableConnecting Onkyo uComponents Connecting a Recording ComponentSystem On/Auto Power On Remote ControlConnecting the Antennas Connecting the Power CordPlug the power cord into an AC wall outlet North AmericanAV receiver enters standby mode Turning On/Off the AV ReceiverTurning On Turning OffSelecting the Language for the Onscreen Setup Menus Controlling Contents of USB or Network DevicesPlayback Playing the Connected ComponentUnderstanding Icons on the Display Playing an iPod/iPhone via USBEnter Playing a USB Device Listening to Internet RadioListening to Other Internet Radio Registering My Favorites*1Top menu of Internet Radio Windows Media Player 11 Setup Windows Media Player 12 SetupPlaying Music Files on a Server Remote PlaybackUsing Remote Playback Using the TunerTuning into Radio Stations Listening to AM/FM RadioPresetting AM/FM Stations Using RDS excluding North American and Taiwan modelsMode Displaying Radio Text RT Finding Stations by Type PTYListening to Traffic News TP Using Basic Functions Using the Automatic Speaker SetupMeasurement procedure First measurement positionWhen you’ve finished making the settings, press ` CancelUse q/wto select a target, and use e/rto change the setting Press Enter Disconnect the speaker setup microphoneError Messages Changing the Speaker Setup ManuallyUsing the Listening Modes Selecting Listening ModesFollowing audio formats are supported by the listening mode About Listening ModesExplanatory Notes Input SourceOnkyo-Original DSP Listening Modes Listening ModesDTS DSD*6Audyssey DSX *8 THXListening Mode Description Input Speaker Source Layout Using the Home Menu Using the Sleep TimerSetting the Display Brightness Using the Whole House Mode Displaying Source InformationChanging the Input Display VCR/DVRUsing Headphones Selecting Speaker LayoutMuting the AV Receiver Press Receiver followed by SP Layout repeatedly to selectUsing Easy Macros RecordingAdvanced Setup On-screen Setup MenusCommon Procedures in Setup Menu Explanatory NotesInput/Output Assign Monitor OutHdmi Input Component Video InputBD/DVD, VCR/DVR, CBL/SAT, GAME, PC TV/CD, PHONO, Port BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX TV/CD, PHONO, PortSpeaker Setup Speaker SettingsDigital Audio Input Analog Audio InputSubwoofer Phase FrontCenter*1, Surround*1, Surround Back*2*3*4 Front Wide*1*2*4, Front High*1*2*4Wireless Subwoofer Speaker DistanceLevel Calibration UnitEqualizer Settings THX Audio SetupBGC Audio Adjust Multiplex/MonoDolby Theater-Dimensional Audyssey DSXLFE Level Source Setup AudysseyIntelliVolume SyncName Edit Picture Adjust To correct a characterWide Mode*1*2 Picture Mode*1Resolution*3*5 Game Mode*3*4*5Film Mode*3*5*6 Edge Enhancement*3*5*6Audio Selector Listening Mode Preset Charge ModeHardware Setup Volume SetupOSD Setup MiscellaneousMulti Zone TunerAuto Standby Audio TV OutAudio Return Channel Lip SyncFirmware Update NetworkDhcp Remote Controller Setup Lock SetupUsing the Audio Settings Dolby Volume Speaker LevelsLate Night Music Optimizer Re-EQMusic Optimizer Re-EQConnecting Your Zone 2 Speakers Directly to the AV receiver Connecting the Zone Speakers to an Additional AmplifierMulti Zone Making Multi Zone ConnectionsOperating on the remote controller Controlling Zone 2/3 Components8RECEIVER Adjusting the Volume for Zones Adjusting the Tone and Balance of ZoneMuting Zones Using a Multiroom Kit with Zone Using a Multiroom Kit with a CabinetUsing a Multiroom Kit with Other Components Using the Onkyo Dock IPod/iPhone Playback via Onkyo DockUP-A1 Dock Controlling Your iPod/iPhone RI DockAvailable buttons RandomLooking up for Remote Control Code Press Receiver followed by SetupUse q/wto select a category, and then press Use q/w/e/rto select a character, and then pressEntering Remote Control Codes Remote Control Codes for Onkyo Components Connected via u Resetting Remote Mode ButtonsResetting the Remote Controller Controlling Other ComponentsEnter Setup Search Repeat Random Mode VCR/PVR8SOURCE*1 Input Guide TOP MenuLearning Commands Deleting Acquired CommandsFollowing buttons cannot learn new commands RemoteUsing Normal Macros Making MacrosRunning Macros Deleting MacrosTroubleshooting PowerAudio There’s no sound with a certain signal format Can’t select the Pure Audio listening modeSpeaker volume cannot be set as required About DTS signalsRemote Controller VideoTuner UP-A1 Dock for iPod/iPhone RecordingZone 2/3 Music Server and Internet RadioUSB Device Playback OthersImportant Note Regarding Video Playback Component Video Monitor OUTFirmware Update Update procedureUpdating the Firmware via Network Before you startTroubleshooting Errors during an update via networkUpdating the Firmware via USB Press Receiver followed by Setup on Remote controller Using 8ON/STANDBY on the front panel, turnErrors during an update via USB Select via USB and press EnterConnection Tips and Video Signal Path Video Connection FormatsAudio Connection Formats OUTVideo Resolution Chart OutputOutput Input 4K *2 1080p/24 1080i 720p 480p/576p 480i/576iUsing an RIHD-compatible TV, Player, or Recorder About p-compatible componentsOperations that can be performed with Connection How to connect and setup Confirm the connecting and settingConfirm the settings Operate with the remote controllerAbout Hdmi Supported Audio FormatsAbout Copyright Protection Network/USB Features Connecting to the NetworkNetwork Requirements Server Requirements USB Device RequirementsServer playback Remote playbackSupported Audio File Formats About DlnaSpecifications Amplifier Section Tuner SectionVideo Section GeneralAudio Outputs OthersMemo 4 0 0 7 0